Check and adjust electromagnetic clutch axial play

AR83.55-W-7682-01A	Check and adjust electromagnetic clutch axial play
	Adapter cable for electromagnetic clutch at compressor	WF58.50-N-4781-01A
	Screw/bolt for removing pressure plate	WF58.50-N-8355-02A

Modification notes

6.12.10

Puller special tool added.

Operation steps 11, 13

*000589000500

Test and adjustment values for refrigerant compressor

Number	Designation		Model 374, 375, 940, 942, 943, 944, 949, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976, 930, 932, 933, 934


BE83.55-N-1001-01B	Axial play of pressure plate	mm	0.5 (0.15)

 Refrigerant compressor

Number	Designation		Model 374.6, 375.4, 940, 942, 943, 944, 958.4	Model 374.5, 375.1, 375.3, 949, 950.5, 950.6, 952.5, 952.6, 953.6, 954.5, 957, 958.0, 958.2, 970, 972, 974, 975, 976


BA83.55-N-1004-01C	Screw/bolt, pressure plate to compressor shaft	Nm	20	20

 Refrigerant compressor

Number	Designation		Model 930, 932, 933, 934, 950.0, 950.1, 950.2, 950.3, 952.0, 952.1, 952.2, 952.3, 953.1, 953.3, 954.0, 954.1, 954.2


BA83.55-N-1004-01C	Screw/bolt, pressure plate to compressor shaft	Nm	20

Check and adjust electromagnetic clutch axial play

001 589 53 21 00

Dial indicator holder

Dial indicator

Puller

000 589 00 05 00

363 589 02 21 00

W83.55-1004-01

Checking

1 Clamp refrigerant compressor in a vise.

 Use two aluminum protective jaws.

2 Position  dial indicator holder with  dial indicator such that tracer pin of  dial indicator rests next to a rivet on pressure plate (1) when under tension (arrow).

3  Move dial indicator to zero position.

W83.55-1005-02

4 Connect crocodile clip (a) and female disconnect (b) of shop-made adapter cable to electrical connections of solenoid.

5 Connect adapter cable to a DC voltage source with 24 V.

6 Read off measurement for axial play of pressure plate (1) on the  dial indicator.

7 Repeat measuring procedure at two additional points of the pressure plate (1) in the same manner.

8 Determine mean value from the three measured values and compare against the specified value.

 If the mean value is not within the specified tolerance range, then the axial play of the pressure plate (1) must be adjusted.

9 Detach the adapter cable from the DC voltage source.

10 Remove adapter cable and  dial indicator holder with  dial indicator from refrigerant compressor.

W83.55-1037-01

Adjust

11 Remove pressure plate (1).

 Counterhold pressure plate (1) with  puller (20). If the pressure plate (1) is stuck in place, use the shop-made bolt to detach the pressure plate (1).

W83.55-1006-01

12 Adjust axial play of pressure plate (1) using spacers (2).

 The spacers (2) are included in the "Connector parts kit".

W83.55-1037-01

13 Install pressure plate (1)  .

 Counterhold pressure plate (1) with  puller (20).

14 Check axial play of pressure plate (1) again.

 Repeat testing and adjustment operations until the determined value is within the tolerance range.

Povezani dokumenti