ar2751d080002b

Insert/measure K1 clutch pack

Vrsta ar · tema 27.51 · različica 0102 · 2007-09-10

Velja za: TRANSMISSION 722.681 ## as of 3947440 in MODEL 902.6, 903.6, 904.6, 905.6 TRANSMISSION 722.681 ## as of 3947440 in MODEL WD1, WD2, WD3, WD6, WD7, XD1, XD2, XD3, XD4, XD5, XD6, XD7, YD1, YD2, YD3, YD4, YD5, YD6, YD7

Ni na voljo v jeziku »sl«; prikazano v jeziku Angleščina.

Umestitev

Funkcijska skupina 2 Podvozje › 27 Samodejni menjalnik › 27.51 Garnitura delov za obnovo sklopke, lamelna zavora — Serija 902 (modeli 6**) · Serija 903 (modeli 6**) · Serija 904 (modeli 6**) · Serija 905 (modeli 6**)

EinPAS 17 pogonski sklop/prema › 17.20 menjalnik › 17.20.54 lamelna zavora/lamelna sklopka — Serija 902 (modeli 6**) · Serija 903 (modeli 6**) · Serija 904 (modeli 6**) · Serija 905 (modeli 6**)

Velja tudi za motorje/menjalnike: 722 681

AR27.51-D-0800-02B

Insert/measure K1 clutch pack

Automatic transmission fluids (ATF, Sheet 236.10)

Sheet 236.10

BB00.40-P-0236-10A

Test and adjustment values

Number

Designation

Trans-mission 722.681 as of trans. no. 3947440

BE27.51-N-1004-01A

Disk play of multi-disk clutch K1

mm

2,80 to 3,20

Insert/measure K1 clutch pack

Thrust device

208 589 00 21 00

Insert/measure K1 clutch pack

D27.51-1125-01

1 Put together externally toothed plates (12, 14) and internally toothed plates (13) in the sequence shown and insert individually.

Place new externally toothed plates and internally toothed plates in ATF oil 1 h before installation. The lining side of the externally toothed plates and internally toothed plates must face towards the output side.

Design of multiple-disc clutch

1 External plate carrier K1

6 Piston K1

11 Disk spring

12 Externally toothed plates (2.07 mm)

13 Internally toothed plates

14 Externally toothed disk (4.0 mm)

15 Circlip

L Toothed plate play

Insert/measure K1 clutch pack

D27.51-1131-01

2 Install circlip (15).

Both ends of the circlip (15) must be seated on a shackle of the external plate carrier K1 (1) (arrows).

Insert/measure K1 clutch pack

3 Mount pressure device on the externally toothed plate (14).

4 Press clutch pack together as far as the end stop using pressure device and a lever press.

The marking ring (bottom arrow) must still be visible.

5 Using a feeler gauge, check the toothed plate play (L) at three points between the circlip (15) and externally toothed plate (14).

To measure the toothed plate play (L) the circlip (15) must abut with the upper contact surface of the groove.
If necessary, adjust the toothed plate play (L) by installing a circlip (15) of corresponding thickness.

D27.51-1104-03

Povezani dokumenti