Adjust front door

AR72.10-P-0550RT

Adjust front door

11.5.09

11.5.09

Value modified: Bolt, door hinge to A-pillar

*BA72.10-P-1004-01P



Inspect, set

 Danger!

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

When moving components, ensure that no body parts or limbs are within the operating range of moving parts.

AS00.00-Z-0011-01A

1

Remove locking eye (1)

2

Check gap between front fender and front door (I) on door

*BE60.00-P-1002-01S

 Feeler gauge

*129589032100

3

Check gap between front door and rear door (S) and gap between front door and rear door in area of B-pillar (K) on door

*BE60.00-P-1003-01S

*BE60.00-P-1004-01S

 Feeler gauge

*129589032100

4

Check gap between front door and door sill molding (T) and gap between front door and A-pillar (J) on door

*BE60.00-P-1002-01S

*BE60.00-P-1004-01S

 Feeler gauge

*129589032100

5

Loosen bolts for door hinge on A-pillar (3) and adjust by moving gap between front fender and front door (I)

*BE60.00-P-1002-01S

 Feeler gauge

*129589032100

6

Adjust gap between front door and rear door (S) and gap between front door and rear door in area of B-pillar (K)

*BE60.00-P-1003-01S

*BE60.00-P-1004-01S

 Feeler gauge

*129589032100

7

Adjust gap between front door and door sill molding (T) and gap between front door and A-pillar (J)

*BE60.00-P-1002-01S

*BE60.00-P-1004-01S

 Feeler gauge

*129589032100

8

Tighten bolts on door hinge on A-pillar (3)



*BA72.10-P-1004-01P

9

Loosen bolts on door hinge on front door (4) and adjust transition between front fender and front door by moving front door

 The contour of the front fender must be flush with the door paneling or should not be protrude more than 1 mm.

10

Tighten bolts for door hinge on front
door (4)



*BA72.10-P-1003-01P

11

Install locking eye (1)

 Do not tighten screws (2).

12

Completely close front door and adjust transition between front door and rear door or in relation to B-pillar by moving locking eye (1)

 Contour of front door should be flush with contour of rear door or B-pillar and should not protrude more than 1 mm.

13

Tighten screws (2)



*BA72.10-P-1005-01P

Number

Designation

Model 251

BE60.00-P-1002-01S

Gap dimension

Fender/engine hood

Dim. "F"

mm

3.5 (1)

Engine hood to A-pillar

Dim. "G"

mm

3.5 (1)

Fender to A-pillar

Dim. "H"

mm

3.5 (1)

Front fender to front door

Dim. "I"

mm

4 (1)

Front door to A-pillar

Dim. "J"

mm

4 (1)

See figure in

-

BE60.00-P-1003-01S

Gap dimension

Front door to rear door in area of B-pillar

Dim. "K"

mm

4.5 (1)

Rear door to roof frame

Dim. "L"

mm

4 (1)

Rear door to C-pillar

Dim. "M"

mm

4.5 (1)

Rear-end door to side wall

Dim. "N"

mm

5.5 (1)

Rear-end door glass to side wall

Dim. "O"

mm

5.5 (1)

See figure in

-

BE60.00-P-1004-01S

Gap dimension

Rear-end door to side wall

Dim. "P"

mm

5.5 (1)

Rear door to rear fender

Dim. "Q"

mm

4 (1)

Rear door to door sill molding

Dim. "R"

mm

6 (0,5)

Front door to rear door

Dim. "S"

mm

4 (1)

Front door to door sill molding

Dim. "T"

mm

5 (0.5)

See figure in

-

Number

Designation

Model 251

BA72.10-P-1003-01P

Bolt, door hinge to front door

Nm

32

BA72.10-P-1004-01P

Bolt, door hinge to A-pillar

Nm

37

BA72.10-P-1005-01P

Bolt, locking eye to B-pillar

Nm

28