W15.12-1002-09
1 | Cylinder head cover | T1.2a | Cylinder 2 ignition coil | T1.5a | Cylinder 5 ignition coil | ||
2 | Heat shield | T1.3a | Cylinder 3 ignition coil | T1.6a | Cylinder 6 ignition coil | ||
3 | Insulating tubing | T1.4a | Cylinder 4 ignition coil | Pfeil | Sealing | ||
T1.1a | Cylinder 1 ignition coil |
Danger | Risk of explosion due to escaping combustible gas or overheating of gas cylinders.Risk of injury caused by burns to skin and eyes. Risk of frostbite to body parts caused by escaping gas and by touching components near the valves when emptying gas cylinders. Risk of poisoning or suffocation caused by inhaling gas. | Remove any sources of ignition. | |
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines. | |
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
Topical note | Notes on tilting the cab | ||
Notes on work safety regulations for vehicles with natural gas-powered engines | |||
| Remove/install | ||
1 | Switch off ignition | ||
2 | Tilt cab | ||
3 | Remove soundproofing | ||
4 | Remove heat shield (2) of air filter housing | Only when removing the ignition coil for cylinder 6 (T1.6a). | |
5 | Clean area around the relevant cylinder 1 bis 6 ignition coil (T1.1a to T1.6a) on the cylinder head cover (1) | ||
6 | Mark electrical connections of cylinder 1 to cylinder 6 ignition coils (T1.1 to T1.6) relative to the respective cylinder | Only for removal of a number of cylinder 1 to cylinder 6 ignition coils (T1.1a to T1.6a). | |
Installation: Note marking of the electrical connections for cylinder 1 to cylinder 6 ignition coils (T1.1a to T1.6a). | |||
7 | Unclip electrical line of the relevant cylinder 1 to 6 ignition coil (T1.1a to T1.6a) at the cylinder head cover (1) | ||
8 | Disconnect electrical connections of the respective cylinder 1 to 6 ignition coils (T1.1 up to T1.6) | ||
9 | Unlock securing clamp of the respective cylinder 1 to 6 ignition coils (T1.1a to T1.6a) and fold upwards | ||
10 | Carefully pull out respective cylinder 1 to 6 ignition coils (T1.1a to T1.6a) on securing clamp and put aside | Installation: Coat the affected ignition coil of cylinder 1 to 6 (T1.1a to T1.6a) in the area of the sealing (arrow) with a little lubricant. | |
Spark plug connector grease | |||
11 | Replace insulating tubings (3) of cylinder 1 to 6 ignition coils (T1.1a to T1.6a) | Only when replacing spark plugs. | |
| |||
| Clean | ||
12 | Clean slot of the removed cylinder 1 to 6 ignition coils (T1.1a to T1.6a) in cylinder head and blow out with compressed air | ||
13 | Clean removed cylinder 1 to 6 ignition coils (T1.1a to T1.6a) | ||
14 | Install in the reverse order |
Documente menționate
- ah0010n100004a Indicaţii privind reglementările de siguranţă a muncii pentru autovehicule cu motoare pe GPL
- ah6080n000301a Indicaţii pentru rabatarea cabinei şoferului
- ap1510w158501la Înlocuire furtunuri izolatoare ale bobinelor de inducţie
- as0000z001801a Pericol de explozie prin scurgeri de gaze inflamabile sau prin supraîncălzirea rezervoarelor de gaz. Pericol de rănire prin arsuri ale pielii şi ochilor. Pericol de îngheţ pentru membre prin scurgeri de gaz şi prin atingerea compone
- as0000z003501a Pericol de moarte în cadrul lucrărilor la componentele şi sistemele cu U >= 30 V tensiune alternativă (CA) respectiv cu U >= 60 V tensiune continuă (CC)
- as6080z000101a Pericol de rănire prin prinderea şi strivirea la basculare cabină şofer