P77.30-2482-06
Model 207.4, shown at left side of vehicle
9 Soft top compartment lid lock
14 Rear seat backrest
15 Panel
16 Side paneling
17 Seat belt
18 Cover
19 Screw
S84/22 Soft top compartment cover in catch position limit switch
P77.30-2481-06
Model 209.4, shown at left side of vehicle
1 Expansion clip
2 Cover
3 Panel
4 Bolts
P77.30-2480-09
Shown on model 209.4, on left side of vehicle
7 Screw
9 Soft top compartment lid lock
S84/22 Soft top compartment cover in catch position limit switch
10 Bolts
11 Bolts
| Remove/install | ||
Danger! | Risk of injury when performing check and repair work in area of roll bar | Before working in the area of the roll bar, pull out the rear head restraints by hand. Keep body parts out of the area where the roll bar extends. | |
Danger! | Risk of injury caused by moving parts that can pinch, crush or, in extreme cases, even sever extremities | No parts of the body or limbs should be within the operating range of the mechanism when moving components. | |
Danger! | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. | |
1 | Remove separation screen | Model 207.4 | |
Model 209.4 | |||
2 | Unclip cover (15) from cover (18) starting at rear seta backrest (14) (arrow A). | Model 207.4 | |
Installation: Ensure that cover (15) is seated correctly in cover (18). | |||
3 | Slide cover (15) downward along seat belt (17). | Model 207.4 | |
4 | Unscrew bolt (19) | Model 207.4 | |
5 | Unclip cover (18) upward and remove | Model 207.4 | |
Installation: Ensure that cover (18) is seated correctly below side paneling (16). | |||
6 | Remove rear seat and rear seat backrest (14) | Model 209.4 | |
7 | Remove expansion clip (1) and remove cover (3) | Model 209.4 | |
8 | Unscrew screws (4) and remove cover (2) | Model 209.4 | |
9 | Unscrew bolt (7) from soft top compartment lid limit switch in catch position (S84/22) | ||
10 | Unclip soft top compartment lid limit switch in catch position (S84/22) and lay down to side with electrical line connected | ||
11 | Remove bolts (10) | Mark installation position of bolts (10). | |
| |||
12 | Press rear seat backrest (14) toward front in area of head restraint until bolts (11) are accessible | Model 207.4 | |
Do not press rear seat backrest (14) too far upward, otherwise the fastening points on the rear seat backrest (14) can be damaged. | |||
Support rear seat backrest (14) with suitable object so that the bolts (11) can be screwed in. | |||
13 | Remove bolts (11) | Mark installation position of bolts (11). | |
| |||
14 | Remove soft top compartment lid lock (9) | ||
15 | Install in the reverse order |
Soft top
Documentos referenciados
- ar6850p3000ec
- ar6850p3000qa
- ar9112p1700qa
- as0000z000901a Risco de lesão através de aprisionamento ou esmagamento, em casos extremos, seccionamento de membros ao tocar partes mecânicas
- as0000z001701a Risco de lesão por corte ou arranhão em peças com cantos cortantes ou rebarbas nos veículos
- as9100z000301qa Risco de lesão na região da estrutura protetora contra capotamento em serviços de inspeção e manutenção