Retrofit antenna for satellite radio mode for Communication and Navigation System (CNS)

AZ82.85-S-0014-01E

Retrofit antenna for satellite radio mode for Communication and Navigation System (CNS)

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

Model

447.6/7

with code W50 (Rear-end door, double-wing, 180 degrees without window)

with code ZU7 (National version for Canada)

except code W54 (2-wing rear-end door, 270 degrees)

except code W65 (Tailgate)

Model

447.6/7

with code W50 (Rear-end door, double-wing, 180 degrees without window)

with code ZU8 (National version for USA)

except code W54 (2-wing rear-end door, 270 degrees)

except code W65 (Tailgate)

Model

447.6

with code W54 (2-wing rear-end door, 270 degrees)

with code ZU7 (National version for Canada)

except code W50 (Rear-end door, double-wing, 180 degrees without window)

except code W65 (Tailgate)

Model

447.6

with code W54 (2-wing rear-end door, 270 degrees)

with code ZU8 (National version for USA)

except code W50 (Rear-end door, double-wing, 180 degrees without window)

except code W65 (Tailgate)

1

Satellite radio antenna

2

Antenna line

3

Antenna plug

1

Satellite radio antenna

2

Antenna line

E21/1

Rear-end door third brake light

1

Clean satellite radio antenna in installation area of roof paneling (1).

 For this purpose, use the cleaner included in the parts kit.

2

Position satellite radio antenna (1), as shown, on roof paneling.

 The satellite radio antenna (1) is magnetic.

3

Route antenna line (2), as shown, from installation area for satellite radio antenna (1), below third brake light  on rear-end door (E21/1), through installation opening (arrow) in roof frame at rear up to right D-pillar.

 Do not kink antenna line (2) and ensure it is routed without chafing.
This will prevent damage occurring.

4

Fasten antenna line (2) in roof frame at rear, section by section, using cable ties to factory-installed electrical wiring harness.

Model 447.7

2

Antenna line

5

Rear headliner

3

Antenna plug

6

Front headliner

Shown on model 447.6 with code D51 (Full-width partition wall with 1 window) on model 447.6

2

Antenna line

6

Front headliner

3

Antenna plug

7

Partition wall

5.1

Model 447.7
Route antenna line (2), as shown, over the roof lining at the rear (5), over the roof lining at the front (6) up to installation location of Communication and Navigation System (CNS) head unit.

 Do not kink antenna line (2) and ensure it is routed without chafing.
This will prevent damage occurring.

5.2

Model 447.6
Route antenna line (2), as shown, along the right roof paneling, over the roof lining at the front (6) up to the installation location of the CNS head unit.

 Do not kink antenna line (2) and ensure it is routed without chafing.
This will prevent damage occurring.

 Model 447.6 with code D50 (Full-width partition wall) Model 447.6 with code D51 (Full-width partition wall with 1 window)
Route antenna line (2) upwards through opening in partition (7).

6.1

Model 447.7
Attach antenna line (2) section by section using tape over the roof lining at the rear (5) and over the roof lining at the front (6).

 Do not route or fasten antenna line (2) in operating and deployment range of window airbag. The tensioning straps of the window airbag must under no circumstances be wrapped.
Otherwise, the functionality of the window airbag may be impaired.

If necessary,

6.2

Model 447.6
Attach antenna line (2) section by section using cable ties to the factory-installed electrical wiring harness.

 Do not route or fasten antenna line (2) in operating and deployment range of window airbag. The tensioning straps of the window airbag must under no circumstances be wrapped.
Otherwise, the functionality of the window airbag may be impaired.

If necessary,