P91.10-3195-09
Shown on vehicle with code (S17) Seat heater (FFO) and code (C54)
Sound system 2
1 Seat
2 Screw
3 Seat belt
4 Seat belt guide
5 Bolts
6 Screw
X28/4 Driver seat heated cushion connector (with code (S17) Seat heater (FFO))
X28/5 Front passenger seat heated cushion connector (with code (S17) Seat heater (FFO))
7 Bracket
8 Bracket (series on driver seat,
on front passenger seat only for code (S17) Seat heater (FFO) or code (I13) Sidebags (FFO))
Modification notes
| Remove/install | ||
Danger! | Risk of injury caused by backrest suddenly folding forward if release lever is accidentally operated during inspection and repair work | When working on the seat, be careful not to accidentally release the backrest mechanism allowing the seat to fold forward. Keep body parts clear of the backrest travel area. | |
1 | Disconnect ground line of battery | On vehicles with code (I13) Sidebags (FFO) | |
2 | Unhook seat belt (3) from belt guide (4) on seat (1) | ||
3 | Remove bolt (6) from belt end fitting of seat belt (3) | | |
4 | Slide seat (1) forwards, fold down backrest and unscrew bolts (5) | Push seat (1) backwards slightly to ensure that it has audibly engaged into both seat rails. | |
Installation: Screw in bolts (5) up to contact surface, tighten right bolt first, then tighten left bolt (5). Move seat (1) to rearmost position, tighten left bolt and then tighten right bolt (2). On vehicles with code (RHD) Right-hand drive vehicle, pay attention to the installation position of the rear spacer sleeves underneath the left seat (1). | |||
| |||
5 | Move seat (1) to rearmost position and remove bolts (2) | Push seat (1) forwards slightly to ensure that it has audibly engaged into both seat rails. Set seat backrest to vertical position. | |
Installation: Screw in bolts (2) up to contact surface and move seat (1) to foremost position. On vehicles with code (RHD) Right-hand drive vehicle, pay attention to the installation position of the front spacer sleeves underneath the right seat (1). | |||
6 | Expose wiring harness at holder (7) | On vehicles without code (C54) Sound system 2, the bracket (7) is clipped into the front cross strut of the seat (1). | |
7 | Tilt seat (1) backwards and expose wiring harness on bracket (8) | Only on driver seat in vehicles with code (S17) Seat heater (FFO) or code (I13) Sidebags (FFO) or seat belt buckle detection on front passenger seat. | |
8 | Disconnect driver seat heated cushion connector (X28/4) and front passenger seat heated cushion connector (X28/5) | On vehicles with code (S17) Seat heaters (FFO) | |
9 | Detach driver seat sidebag connector and front passenger seat sidebag connector | On vehicles with code (I13) Sidebags (FFO) | |
10 | Detach driver seat ETR [GUS] connector (2-pin) or front passenger seat ETR [GUS] connector (2-pin) | On vehicles with seat belt buckle detection | |
11 | Remove seat (1) from vehicle | Carefully remove seat (1) out of vehicle with a helper, as otherwise trim parts and detachable parts may be damaged. | |
On vehicles with code (RHD) Right-hand drive vehicle, spacer sleeves for aligning the seat (1) are located underneath the right seat (1) in the front as well as underneath the left seat (1) in the rear in each case. | |||
12 | Install in the reverse order | ||
13 | Check supplemental restraint system using STAR DIAGNOSIS | ||
| Connect STAR DIAGNOSIS and read out fault memory |
Front seats
Seat belts/emergency tensioning retractors
Powiązane dokumenty
- ad0000p200004mcc
- ar5410p0003mcc Odłączanie, podłączanie przewodu masowego akumulatora
- as9100z000501v Niebezpieczeństwo obrażeń w wyniku nagłego przechylenia do przodu oparcia fotelaw przypadku niekontrolowanego uruchomienia dźwigni odblokowania podczas prac diagnostycznych i naprawczych