Remove/install engine hood catch

AR88.40-S-3200E

Remove/install engine hood catch

21.12.15

Model

447, 448

Shown on MODEL 447.8 with CODE JS1 (360 degree camera)

1

Mounting clip

2

Radiator grille

Shown on MODEL 447.8 with CODE FY1 (Theft protection package)

3

Engine hood

7

Lower section of engine hood catch

11

Spring clip

4

Upper section of engine hood catch

8

Cover

12

Nuts

5

Nut

9

Electrical connector

S62/41

Engine hood switch

6

Upper crossmember

10

Cable

 Danger !

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

 

Remove/install

1

Open engine hood (3)

2

Remove retaining clips (1) and radiator grille (2)

 Installation: Check the retaining clips (1) for damage.
Ensure that radiator grille (2) is seated correctly.

for damage



Replace respective retaining clip (1)

3

Mark installation position of engine hood lock top section (4) on engine hood (3)

4

Unscrew nuts (5) and remove engine hood catch upper section (4)

 Installation: Align engine hood lock top section (4) at made markings.

 Bolt/nut, engine hood catch to engine hood

*BA88.40-N-1003-01G

5

Disconnect electrical connector (9)

Model 447, 448.8
with code FZ5 (Anti-theft alarm system)
Model 447
with code FY1 (Anti-Theft Protection package)

6

Lift catch hooks (arrows A) with suitable screwdriver, and unclip cover (8) with engine hood switch (S62/41)

Model 447, 448.8
with code FZ5 (Anti-theft alarm system)
Model 447
with code FY1 (Anti-Theft Protection package)

 Installation: Ensure that hook (arrow B) is seated correctly in engine hood lock bottom section (7).
Ensure that hooks (arrows A) are seated correctly on engine hood lock bottom section (7).

7

Lift spring U-bolt (11) and unhook cable (10) from engine hood lock bottom section (7)

 Installation: Ensure that cable (10) is seated correctly in engine hood lock bottom section (7).

8

Mark installation position of engine hood lock bottom section (7) on upper crossmember (6)

9

Unscrew nuts (12)

 Bolt/nut, engine hood catch to lock carrier

*BA88.40-N-1002-01G

10

Remove engine hood catch lower section (7)

 Installation: Check engine hood catch lower part (7) for sluggishness.

If complaint present



Replace engine hood catch lower part (7)

11

Install in the reverse order



Check

12

Pull engine hood (3) upward with a slight jerk

 To check correct locking of engine hood catch.

Engine hood (3) can be opened.



Adjust engine hood catch

13

Release engine hood (3) and check that engine hood catch upper part (4) engages correctly

14

Close engine hood (3)

15

Move wiper motor to parked position

Model 447, 448.8
with code FZ5 (Anti-theft alarm system)
Model 447
with code FY1 (Anti-Theft Protection package)

AR82.30-S-6800-01E

 By turning wind deflector to park position, the function of the engine hood switch (S62/41) is checked.

16

Open engine hood (3)

Model 447, 448.8
with code FZ5 (Anti-theft alarm system)
Model 447
with code FY1 (Anti-Theft Protection package)

17

Close engine hood catch lower part (7) with suitable tool, and lock vehicle with remote control

Model 447, 448.8
with code FZ5 (Anti-theft alarm system)
Model 447
with code FY1 (Anti-Theft Protection package)

 To check alarm triggering function.
The anti-theft alarm system (ATA) is activated after approx. 10 seconds.

18

Unlock engine hood catch lower part (7) with suitable tool

Model 447, 448.8
with code FZ5 (Anti-theft alarm system)
Model 447
with code FY1 (Anti-Theft Protection package)

 The alarm must be triggered.
The alarm can be switched off with the remote control when opening the vehicle.

19

Close engine hood (3)

Model 447, 448.8
with code FZ5 (Anti-theft alarm system)
Model 447
with code FY1 (Anti-Theft Protection package)

 Engine hood

Number

Designation

Model 447, 448

BA88.40-N-1002-01G

Bolt/nut, engine hood catch to lock carrier

Nm

12

 Engine hood

Number

Designation

Model 447, 448

BA88.40-N-1003-01G

Bolt/nut, engine hood catch to engine hood

Nm

12