Remove/install radiator grille

AR88.40-D-4001TS

Remove/install radiator grille

28.11.2019

Model

907, 910

Modification notes

14.10.2019

Method extended

Operation step 3

14.10.2019

Method modified.

Step 5

28.11.2019

Method extended

Operation steps 2, 3, 5, 6

Shown on model 907 with code JB6 (Parking package with 360° camera)

1

Radiator trim

3

Lock

5

Front camera

2

Bolts

4

Bumper

Shown on model 910 with code ME0 (electric motor 85 kW)

1

Radiator trim

6

Socket flap

7

Cap

8

Lip

9

Electrical connector

10

Electrical connector

 Danger

Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)

Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.

AS00.00-Z-0035-01A

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

Topical note

General information on handling vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system

AH00.00-Z-0300-01A

 

Remove/install

1

Switch off ignition and store transmitter key outside of transmission range (min. 2  m).

Model 907.6/7
with code JB6 (Parking package with 360-degree camera)
Model 910.6
with code JB6 (Parking package with 360-degree camera)
except code ME0 (Electric motor 85 kW)

2

Open socket flap (6).

Model 910 with engine 780.703
with code ME0 (Electric motor 85 kW)

3

Remove voltage of high-voltage on-board electrical system.

* Applies to Europe only

Model 910 with engine 780.703
with code ME0 (Electric motor 85 kW)

AR47.70-D-1000TE

 Do not close socket flap (6).

4

Remove screw/bolts (2) .

5

Remove cap (7) from external power supply socket.

Model 910 with engine 780.703
with code ME0 (Electric motor 85 kW)


Carefully release locks (arrows).
Damage may occur otherwise.

 For this purpose, use a suitable tool through openings on cap (7) to release locks (arrows) and remove cap (7).

 Installation: Check cap (7) is correctly seated.

6

Remove radiator grille (1) on the bumper (4).

 Model 907
except code JB6 (Parking package with 360-degree camera)
Model 910
except code JB6 (Parking package with 360-degree camera)
except code ME0 (Electric motor 85 kW)
To do so, release the locks (3).

 Model 907.6/7
with code JB6 (Parking package with 360-degree camera)
Model 910.6
with code JB6 (Parking package with 360-degree camera)
except code ME0 (Electric motor 85 kW)
For this purpose, release locks (3) and disconnect electrical connector of front camera (5).

 Model 910 with engine 780.703
with code ME0 (Electric motor 85 kW)
To do this, unlock locks (3) and disconnect electrical connectors (9, 10).

 Installation: Ensure locks (3) are correctly seated. Check locks (3).

 Model 910 with engine 780.703
with code ME0 (Electric motor 85 kW)
Installation: Check that sealing lip (8) of socket recess in radiator grille (1) is correctly seated.

If locks (3) are damaged and are not locked properly,



Replace radiator grille (1) and/or bumper (4).

Remove/install front bumper

AR88.20-D-2000TS

7

Install in the reverse order.



Check

8

Perform function check of front camera (5).

Model 907.6/7
with code JB6 (Parking package with 360-degree camera)
Model 910.6
with code JB6 (Parking package with 360-degree camera)
except code ME0 (Electric motor 85 kW)