ar8830s0025p

Remove/install bumper body-styling bar

Typ ar · temat 88.30 · wersja 0100 · 2019-06-18

Dotyczy: Model 470, 471 with code Y1F (Anodized aluminum brush guard (bull bar)) with code ZJ7 (Model for Australia) Model 470, 471 with code Y1G (Black aluminum brush guard (bull bar)) with code ZJ7 (Model for Australia)

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 88 Części dobudowane, klapy zewnętrzne › 88.30 Części dobudowane, zabezpieczanie przed wjechaniem pod pojazd — Seria 470 · Seria 471

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.38 Zderzak/spojler/okładzina zewnętrzna/schowek/przednie zabezpieczenie › 35.38.44 Okładzina/element ozdobny/osłona przednia — Seria 470 · Seria 471

AR88.30-S-0025P

Remove/install bumper body-styling bar

03.06.2019

Model

470, 471

with code Y1F (Anodized aluminum brush guard (bull bar))

with code ZJ7 (Model for Australia)

Model

470, 471

with code Y1G (Black aluminum brush guard (bull bar))

with code ZJ7 (Model for Australia)

Remove/install bumper body-styling bar

S88.30-A029-09

1

Front grille guard

4

Electrical connector

6

Ground cable

2

Electrical connector

5

Electrical connector

7

Screw

3

Electrical connector

Remove/install bumper body-styling bar

Shown with code EZ8 (PARKTRONIC)

1

Front grille guard

8

Electrical connector

19

Radar sensor

20

Electrical connector

S88.30-A030-06

Remove/install bumper body-styling bar

S88.30-A031-09

1

Front grille guard

12

Bolts

15

Nuts

9

Nuts

13

Bolts

16

Bracket

10

Bracket

14

Washer

17

Bolts

11

Washer

Remove/install bumper body-styling bar

1

Front grille guard

18

Upper half of bumper

S88.30-A032-12

Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Topical note

Notes on self-locking nuts and bolts

AH00.00-N-0001-01A

Remove/install

1

Remove the front fender liner.

AR88.10-S-1301P

2

Remove front engine compartment lining at bottom.

AR61.20-S-1105P

3

Disconnect electrical connectors (2, 5).

4

Disconnect electrical connectors (3, 4).

5

Remove ground line (6).

Remove bolt (7) to do this.

6

Disconnect electrical connector (8).

Model 470, 471 with code EZ8 (PARKTRONIC)

7

Disconnect electrical connector (20) of the radar sensor (19).

8

Loosen bracket (10).

To do this, remove nuts (9) from the screws (12) and remove screws (12) with washers (11).

Nut, antenna bracket to longitudinal frame member bracket

*BA88.30-N-1016-01P

9

Loosen bracket (16).

Remove nuts (15) from the screws (17) and remove screws (17) with the washers (14).

Nut, bracket to longitudinal frame member bracket

*BA88.30-N-1018-01P

10

Remove body-styling bar (1).

To do so, unscrew screws/bolts (13).
Aid of 2 helpers required.

Installation: Mask off top half of the bumper (18) in the hatched area.

Screw, carrier to longitudinal frame member

*BA88.30-N-1021-01P

11

Install in the reverse order.

Check

12

Perform function check of 360° camera.

Model 470, 471 with code JS1 (360° camera)

13

Check radar sensor (19).


Model 470, 471 with code BA3 (Active Brake Assist)

AR30.30-S-1003P

14

Perform function check of headlamp cleaning system.

Model 470, 471 with code LG7 (LED High Performance headlamp)

15

Perform function check of front fog lamps.

AP82.10-S-8251P

Detachable parts, body-styling bar, crossmember

Number

Designation

Model 470, 471

BA88.30-N-1016-01P

Nut, antenna bracket to longitudinal frame member bracket

Nm

50

Detachable parts, body-styling bar, crossmember

Number

Designation

Model 470, 471

BA88.30-N-1018-01P

Nut, bracket to longitudinal frame member bracket

Nm

50

Detachable parts, body-styling bar, crossmember

Number

Designation

Model 470, 471

BA88.30-N-1021-01P

Screw, carrier to longitudinal frame member

Nm

85

Powiązane dokumenty