D83.70-1554-79
Shown on model 907 with code XM1 (Noise abatement measures) |
1 | Fuel line | 5 | Line bracket | |
2 | Expansion rivet | 6 | Line bracket | |
3 | Cover | 7 | Clamp | |
4 | Intake air duct |
Shown on model 907 with code XM1 (Noise abatement measures) |
1 | Fuel line |
8 | Locking element |
9 | Fuel metering pump |
D83.70-1555-76
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Danger | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contactwith fuel. | No fires, sparks, open flames or smoking. Pour fuels into suitable and appropriately marked containers only. | |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
| Remove/install | ||
1 | Switch off ignition and store transmitter key outside of transmission range (min. 2 m). | To prevent the stationary heater from being switched on unintentionally, keep the Telestart transmitter protected against unauthorized or accidental access for the duration of the work on the stationary heater. | |
2 | Lift vehicle with lifting platform. | ||
Topical note | Special instructions for lifting and supporting vehicle | ||
3 | Remove expansion rivets (2) and take off cover (3). | Model 907, 910 with code XM1 (Noise abatement measures) | |
Installation: Reinstall the cover (3) only after the leak test. | |||
Clip remover | |||
4 | Remove intake air duct (4). | ||
5 | Unclip fuel line (1) from line bracket (5). | Clip remover | |
6 | Unclip fuel line (1) from line bracket (6). | ||
7 | Open clamp (7) using a suitable tool and detach fuel line (1) from heater. | Collect escaping fuel with a suitable collecting pan. | |
Installation: Replace clamp (7). | |||
8 | Seal fuel line (1) and connection on heater immediately with suitable stop plugs. | Record plug | |
9 | Release locking element (8). | ||
10 | Unlock fuel line (1) at connection (arrow A) and detach from fuel metering pump (9). | Collect escaping fuel with a suitable collecting pan. | |
11 | Seal connection of fuel line (1) and connection of fuel metering pump (9) immediately with suitable stop plugs. | Record plug | |
12 | Remove fuel line (1). | ||
13 | Install in the reverse order. | ||
| Check | ||
Danger | Risk of explosion caused by fuel vapors igniting, risk of poisoning caused by inhaling combustible gases and risk of injury caused by burns during and after operation of heater unit | Do not operate stationary heater, auxiliary heater or engine with heater booster in closed rooms or when refueling. Allow heater unit to cool down after operation and wear protective gloves. | |
14 | Perform function test of heater. | ||
15 | Check fuel system at heater for leaktightness. | Visual inspection. |
452 589 01 63 00
Clip remover
129 589 00 91 00
Record plug
Powiązane dokumenty
- ah0060n010001ts Wskazówki dotyczące podnoszenia pojazdu, ustawiania na podporach
- ar0060d100004ts
- as0000z000201a Niebezpieczeństwo zranienia skóry i oczy na skutek kontaktu z gorącymi lub żarzącymi się przedmiotami
- as0000z001001a Zagrożenie życia na skutek ześlizgnięcia lub spadnięcia pojazdu z podnośnika.
- as4700z000101a Niebezpieczeństwo wybuchu wskutek zapalenia, niebezpieczeństwo zatrucia wskutek wdychania i połknięcia paliwa oraz niebezpieczeństwo obrażeń wskutek kontaktu skóry i oczu z paliwem.
- as8370z000201a Niebezpieczeństwo wybuchu oparów paliwa, niebezpieczeństwo zatrucia na skutek wdychania spalin i niebezpieczeństwo zranienia na skutek poparzenia podczas lub po fazie grzania.