Remove/install antenna cable

AR82.62-P-1200MCC

Remove/install antenna cable

21.7.11



Removing

1

Remove left front headlamp unit

* not for USA

AR82.10-P-4730MCC

* for USA only

AR82.10-P-4730MCU

2

Remove radio

With code (C50) smart radio 10 or

Code (C57) smart radio 9 or

Code (516) RADIO WITH USB INTERFACE or code (527) High-Line radio or code (P02) car2go with instrument panel up to production date 30.8.10

* not for USA

AR82.60-P-7502MCC

* for USA only

AR82.60-P-7502MCU

3

Remove antenna cable (1) from antenna base (2)

4.1

Remove antenna cable (1) from body in area of upper door hinge

With code (C08) Radio preinstallation with rod antenna (FFO) and

without code (460) Canada version,

without code (494) USA version or without code (498) Japan version

4.2

Detach antenna amplifier (3) from body

With code (460) Canada version

With code (494) USA version or

With code (498) Japan version

5

Remove adhesive tape (4) from protective tube (5) and push protective tube (5) back until main wiring harness is exposed

6

Expose antenna cable (1) at main wiring harness and cut off (arrow A)

 Cut off antenna cable (1) directly at the pushed back protective tube (5).

7

Expose antenna amplifier supply line (6) at main wiring harness and cut off (arrow A)

With code (460) Canada version

With code (494) USA version or

With code (498) Japan version

 Cut off antenna amplifier supply line (6) approx. 5 cm before the pushed back protective tube (5).

8

Make cable hole at grommet (8)

 Cut off pin (7).

9

Cut off antenna cable (1) in radio recess (arrow B)



Install

10

Remove adhesive tape (9) from new antenna cable (1)

11.1

Clip antenna cable (1) into body in area of upper door hinge

With code (C08) Radio preinstallation with rod antenna (FFO) and

Without code (460) Canada version,

without code (494) USA version or without code (498) Japan version

11.2

Clip antenna amplifier (3) into body

With code (460) Canada version

With code (494) USA version or

With code (498) Japan version

12

Screw antenna cable (1) onto antenna base (2) by hand

13

Route antenna cable (1) along main wiring harness and guide through grommet (8) into interior

 Expanding pliers

*450589123700

14

Route new antenna amplifier supply line (6.1) along antenna cable (1) to antenna amplifier supply line (6) at main wiring harness

15

Cut new antenna amplifier supply line (6.1) to length and connect to antenna amplifier supply line (6) using solder connector (10)

With code (460) Canada version

With code (494) USA version or

With code (498) Japan version

 Use solder connector (10) with
Ø 2.4 mm.

AR00.19-P-0100A

16

Push protective tube (5) forward and fix in place using suitable insulation tape

17

Fix antenna cable (1) in place at main wiring harness using suitable insulation tape.

18

Route antenna cable (1) along main wiring harness toward radio recess and fasten using cable tie (11)

19

Fix antenna cable (1) in place at main wiring harness in radio recess using suitable insulation tape

20

Seal grommet (8) using suitable sealant

21

Install left front lamp unit

* not for USA

AR82.10-P-4730MCC

* for USA only

AR82.10-P-4730MCU

22

Install radio

With code (C50) smart radio 10 or

Code (C57) smart radio 9 or

Code (516) RADIO WITH USB INTERFACE or code (527) High-Line radio or code (P02) car2go with instrument panel up to production date 30.8.10

* not for USA

AR82.60-P-7502MCC

* for USA only

AR82.60-P-7502MCU