P77.37-2181-06
11 Hydraulic pump
12 Screw
P77.37-2115-09
1 Nut
2 Hydraulic pump ground cable
3 Nut
4 Hydraulic pump power supply cable
9 Hydraulic lines
11 Hydraulic pump
5 Nut
6 Hydraulic pump bracket
7 Connector
| Removing | ||
Danger! | Risk of injury when performing check and repair work in area of roll bar | Before working in the area of the roll bar, pull out the rear head restraints by hand. Keep body parts out of the area where the roll bar extends. | |
Danger! | Risk of injury caused by moving parts that can pinch, crush or, in extreme cases, even sever extremities | No parts of the body or limbs should be within the operating range of the mechanism when moving components. | |
Danger! | Risk of injury to skin or eyes caused by hydraulic fluid spraying out under high pressure. Risk of poisoning caused by swallowing hydraulic fluid | Depressurize the hydraulic system completely before starting any work on the system. Wear protective clothing and safety glasses. | |
1 | Check supply pressure of hydraulic pump (11) | ||
2 | Open trunk lid | ||
3 | Remove left side wall lining in trunk | ||
4 | Loosen bolt (12) on hydraulic pump (11) | Pressure is relieved from hydraulic system | |
5 | Remove soft top compartment lid of hydraulic cylinder | Lay soft top compartment lid hydraulic cylinder down to side with lines connected. | |
6 | Disconnect plug (7) from hydraulic unit | ||
7 | Unscrew nut (5) from hydraulic pump bracket (6). | ||
8 | Unscrew nut (1) | ||
9 | Remove hydraulic pump ground line (2) | ||
10 | Unscrew nut (3) | ||
11 | Remove hydraulic pump power supply cable (4) | ||
12 | Disconnect hydraulic lines (9) from hydraulic pump (11) | ||
13 | Remove hydraulic pump (11) | ||
| Install | ||
14 | Install hydraulic pump (11) | ||
15 | Connect hydraulic lines (9) to hydraulic pump (11) | ||
16 | Screw on hydraulic pump bracket (6) with nut (5) | ||
17 | Connect plug (7) to hydraulic pump (11) | ||
18 | Install hydraulic pump ground cable (2) | ||
19 | Tighten nut (1) | ||
20 | Remove hydraulic pump power supply cable (4) | ||
21 | Tighten nut (3) | ||
22 | Tighten bolt (12) on hydraulic pump (11) | ||
23 | Install soft top compartment lid hydraulic cylinder | ||
24 | Check hydraulic system oil level | If necessary correct oil level | |
| Hydraulic fluids (Specification 343.0) | Sheet 343.0 | |
Oil filler screw to hydraulic unit reservoir | |||
| |||
25 | Check hydraulic pump (11) for leakage and proper function | ||
26 | Install left side wall lining in trunk | ||
27 | Close trunk lid |
Soft top hydraulic components
Filler syringe
230 589 01 63 00
Powiązane dokumenty
- ar6830p4601qa
- ar7737p100004ka Odłączanie i podłączanie przewodów hydraulicznych do pompy hydraulicznej
- ar7737p4175qa Demontaż i montaż siłownika hydraulicznego pokrywy skrzyni dachuskładanego
- ar7737p420401qa Kontrola ciśnienia tłoczenia pompy hydraulicznej dachu składanego
- as0000z000901a Niebezpieczeństwo zakleszczenia lub zmiażdżenia, w skrajnym przypadku obcięcia kończyn podczas prac przy układach mechanicznych.
- as0000z001301a Niebezpieczeństwo obrażeń oczu i skóry przez płyn hydrauliczny pod ciśnieniem. Niebezpieczeństwo zatrucia w wyniku spożycia płynu hydraulicznego
- as9100z000301qa Niebezpieczeństwo obrażeń w obszarze kabłąka ochronnego podczas napraw i czynności diagnostycznych.
- bb0040p034300a Płyny hydrauliczne (specyfikacja 343.0)