1 | Model badge |
2 | Adhesive tape strips |
3 | Carrier foil |
P88.50-2116-01
S72.20-4684-08
Shown on model 447.7 |
A | 60 mm | B | 173 mm | C | 164 mm |
S72.20-4633-08
Shown on MODEL 447.6 with CODE ZG2 (All-wheel drive, permanent) |
A | 60 mm | C | 164 mm | |
B | 173 mm | D | 20 mm |
S72.20-4685-08
Shown on MODEL 447.7 with CODE ZU8 (National version USA) |
A | 60 mm | B | 173 mm | C | 164 mm |
S72.20-4634-08
Shown on MODEL 447.8 with CODE W65 (Liftgate) |
A | 66 mm | C | 164 mm | |
B | 173 mm |
S72.20-4635-08
Shown on MODEL 447.8 with CODE W64 (Rear window to be opened separately) |
A | 66 mm | C | 86 mm | |
B | 91,6 mm |
S72.20-4636-08
Show on MODEL 447.8 with CODE ZK7 (MARCO POLO equipment line ) and with CODE W65 (Liftgate) |
A | 66 mm | C | 164 mm | |
B | 173 mm |
S72.20-4637-08
Shown on MODEL 447.8 with CODE ZK7 (MARCO POLO equipment line), with CODE W64 (Separately opening rear-end door) and with CODE ZG2 (All-wheel drive, permanent) |
A | 66 mm | D | 14,4 mm | |
B | 91,6 mm | E | 186 mm | |
C | 86 mm | F | 57 mm |
S72.20-4638-08
Shown on MODEL 447.8 with CODE ZK7 (MARCO POLO equipment line) and with CODE W64 (Shown on ) |
A | 66 mm | C | 86 mm | |
B | 91,6 mm |
S72.20-4639-08
Shown on MODEL 447.8 with CODE ZK7 (MARCO POLO equipment line), with CODE W65 (Liftgate) and with CODE ZG2 (All-wheel drive, permanent) |
A | 66 mm | D | 14,4 mm | |
B | 173 mm | E | 188 mm | |
C | 164 mm | F | 57 mm |
4 | Mercedes star |
5 | Liftgate |
6 | Adhesive tape strips |
S72.20-4673-06
| Clean | ||
1 | Clean bonding surfaces on model badge (1) or Mercedes star (4) | | |
Cleaner | |||
Install model designation | |||
2 | Mask model badge (1) with adhesive tape (2) | To fasten individual letters and numbers of model badge (1). | |
3 | Attach adhesive tape to liftgate (5) according to dimensions | Adhesive tape serves as installation aid. | |
4 | Heat liftgate (5) in area of bonding surface on model badge (1) to approx. 40 °C | ||
5 | Remove carrier foil (3) | The individual letters and numbers on the model badge (1) must be fastened on the adhesive strips (2). | |
6 | Align corresponding model badge (1) according to liftgate (5) and glue on | | |
7 | Remove adhesive tape (2) from model badge (1) | ||
8 | Remove adhesive tape to position model badge (1) from liftgate (5) | ||
9 | Mark center axis on liftgate (5) on adhesive strips to position Mercedes star (4) (arrow M) | ||
10 | Glue adhesive strips (6) to Mercedes star (4) in lower area as shown | ||
11 | Extend tip of Mercedes star (4) downward to adhesive strips (6) and mark correspondingly (arrow N) | ||
12 | Heat bonding surface on Mercedes star (4) to approx. 40 °C | ||
13 | Remove carrier foil from Mercedes star (4) | ||
14 | Align Mercedes star (4) on liftgate (5) and glue on | | |
The extension of the upper tip should be flush with the center axis marked on the adhesive strips (6) (arrows M, N). | |||
15 | Remove adhesive tape to position Mercedes star (4) on liftgate (5) and adhesive strips (6) | ||
| Clean | ||
16 | Remove bonding residues from liftgate (5) | Cleaner |