ar7218p1000sm
Remove/install door paneling
Typ ar · temat 72.18 · wersja 0104 · 2010-02-03
Dotyczy: MODEL 450.3 /4 (except 450.418)
Niedostępne w języku „pl”; wyświetlono w języku Angielski.
Umiejscowienie
Grupa funkcyjna 3 Nadwozie › 72 Drzwi › 72.18 Poszycie drzwi bocznych — Seria 450 (modele 3**, 400, 401, 402, 403, 414, 432, 433, 441, 442, 443, 452)
EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.35 Drzwi › 35.35.40 Drzwi przednie — Seria 450 (modele 3**, 400, 401, 402, 403, 414, 432, 433, 441, 442, 443, 452)
EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.35 Drzwi › 35.35.41 Drzwi środkowe — Seria 450 (modele 3**, 400, 401, 402, 403, 414, 432, 433, 441, 442, 443, 452)
EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.35 Drzwi › 35.35.44 Drzwi przesuwne — Seria 450 (modele 3**, 400, 401, 402, 403, 414, 432, 433, 441, 442, 443, 452)
EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.35 Drzwi › 35.35.46 Drzwi tylne — Seria 450 (modele 3**, 400, 401, 402, 403, 414, 432, 433, 441, 442, 443, 452)
AR72.18-P-1000SM
| Remove/install door paneling
| 12.12.08
|
MODEL 450.3 /4 (except 450.418)
1 Crank window seal
2 Door paneling
3 Stop buffer
| Remove/install
|
|
|
| Remove and install door paneling (2) only at a room temperature of 20 °C.
|
|
|
1
| Remove outside mirror
|
| AR88.70-P-9000SM
|
2
| Remove crank window seal (1) upward
| Installation: Carefully insert crank window seal (1) from front toward rear.
|
|
3
| Completely close mechanical or electrical crank window
|
|
|
4
| Press in door paneling (2) from outside (arrows) until top paneling (2) is detached completely from shaft strip over entire length
| When replacing door paneling (2) replace stop buffer (3).
|
|
|
|
| Installation: Observe installation position of door paneling (2). Check gaps, adjust if necessary.
Refer to:
|
|
|
|
| Gap dimensions on hoods, doors and lids
| AR60.00-P-0700-01SM
|
|
|
|
| *BE60.00-P-1002-01H
|
5
| Manually press against bottom edge of door paneling (2) from bottom and slightly move door paneling (2) toward rear.
| Door paneling (2) slips out of door mounts.
Installation: Press against bottom edge of door paneling (2) from bottom until upper door paneling (2) arrests in shaft strip.
|
|
6
| Remove door paneling (2) by slightly rotating downward
| Installation: Insert door paneling (2) into front mount from bottom and carefully guide below door handle (arrows).
|
|
7
| Install in the reverse order
|
|
|
Test and adjustment values for gap dimensions
Number
| Designation
| Model
450.3/4
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
BE60.00-P-1002-01H
| Gap dimension
| Front door to CBS front
| Dimension "H"
| mm
| 8.0 (1.5)
|
|
|
| Front door to roof
| Dimension "L"
| mm
| 7,0 (1,5)
|
|
|
| Front door to bottom side piece
| Dimension "L"
| mm
| 7,0 (1,5)
|
|
|
| Front door to rear fender
| Dimension "L"
| mm
| 7,0 (1,5)
|
Powiązane dokumenty
