S72.10-1007-06
1 Striker eye
2 Door hinges
Adjust | |||
Danger! | Risk of injury to fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/tailgate or sliding roof. | When moving components, ensure that no body parts or limbs are within the operating range of moving parts. | |
1 | Remove striker eye (1) | Remove striker eye (1) to prevent damaging the door lock during adjustment. | |
2 | Check gaps on front door | ||
Front door to fender | |||
Front door to roof | |||
Front door to upper sliding door | |||
Front door to lower sliding door | |||
Front door to upper side wall | |||
Front door to lower side wall | |||
Front door to rocker panel | |||
Front door to wheelhouse | |||
3 | Remove outside mirror | ||
4 | Loosen door hinges (2) | Have a second person assist you. | |
5 | Adjust gaps by moving front door | Have a second person assist you. | |
Front door to fender | |||
Front door to roof | |||
Front door to upper sliding door | |||
Front door to lower sliding door | |||
Front door to upper side wall | |||
Front door to lower side wall | |||
Front door to rocker panel | |||
Front door to wheelhouse | |||
6 | Tighten door hinges (2) | Repair paint damage on bolts | |
| |||
| |||
Torque wrench | |||
7 | Install striker eye (1) | Do not tighten | |
8 | Adjust striker eye (1) by moving | The front door should be closed completely to adjust the correct installation depth. | |
The front door should be flush with the B-pillar following adjustment or should not extend more than 1 mm | |||
9 | Tighten striker eye (1) | | |
Torque wrench | |||
10 | Install outer mirror | ||
| Check | ||
11 | Check door for easy motion | ||
12 | Check gaps on front door again and adjust if necessary | ||
Front door to fender | |||
Front door to roof | |||
Front door to upper sliding door | |||
Front door to lower sliding door | |||
Front door to upper side wall | |||
Front door to lower side wall | |||
Front door to rocker panel | |||
Front door to wheelhouse |
Test and adjustment values for gap dimensions
Number | Designation | Model 638 | |||
BE60.00-N-1002-01A | Size of gap | Front door to fender | Dim. "B" | mm | 6.01 |
Front door to roof | Dim. "C" | mm | 8.01 | ||
Front door to upper sliding door | Dim."D" | mm | 7.01 | ||
Front door to lower sliding door | Dim. "E" | mm | 7.01 | ||
Front door to upper side wall | Dim."F" | mm | 6.01 | ||
Front door to lower side wall | Dim."G" | mm | 6.01 | ||
Front door to rocker panel | Dim. "H" | mm | 6.01 | ||
Front door to wheelhouse | Dim. "I" | mm | 6.01 | ||
Fig., see | |||||
Front door
Number | Designation | Model | ||
BA72.10-N-1001-01A | Bolt, door hinge to A-pillar | Nm | 28 | |
BA72.10-N-1002-01A | Bolt, door hinge to door | Nm | 28 | |
BA72.10-N-1003-01A | Bolt, striker eye to B-pillar | Nm | 23 | |
Torque wrench
001 589 72 21 00
Powiązane dokumenty
- ar6000s070001v
- ar8870s9000a
- as0000z001101a Niebezpieczeństwo zranienia przez zakleszczenie lub zmiażdżenie palców podczas demontażu, montażu i prac regulacyjnych przy pokrywach, drzwiach i oknie dachowym.