P72.10-3386-09
1 Retaining clip
2 Front CBS
3 Top cover
4 Bottom cover
5 Door trim
6 Expansion clip
7 Electrical connector
(with code (V43) Power window)
M10/4 Right power window motor
(with code (V43) Power window lifter)
M14/5 Right door CL [ZV] motor
M14/6 Left door CL [ZV] motor
X35/1 Left door separation point
X35/2 Right door separation point
8 Screw
9 Triangular window
17 Electrical connector
M10/3 Left power window motor (with code (V43) Power window lifter)
P72.10-3387-09
5 Door trim
10 Cover
11 Assembly wedge
12 Screw
13 Wiring harness
14 Inside door opener
15 Impact protection
16 Cable
H4/10 Right front speaker
(with code (C08) Radio preinstallation including rod antenna (FFO) or
code (C50) smart radio 10 or
code (C57) smart radio 9 or
code (516) RADIO WITH USB INTERFACE or
code (527) Radio High-Line)
H4/9 Left front speaker
(with code (C08) Radio preinstallation including rod antenna (FFO) or
code (C50) smart radio 10 or
code (C57) smart radio 9 or
code (516) RADIO WITH USB INTERFACE or
code (527) Radio High-Line)
P72.10-3866-11
Shown on left side of vehicle
18 Hip protector (with code (I53) Head/thoraxbag)
19 Spring disks
20 Clamp
P72.10-4020-01
5 Door trim
21 Soundproofing (with code (C17) Sound package (2 tweeter, 2 bass reflex boxes and diplexer) (FFO))
H4/9 Left front speaker
(with code (C08) Radio preinstallation including rod antenna (FFO) or
code (C50) smart radio 10 or
code (C57) smart radio 9 or
code (516) RADIO WITH USB INTERFACE or
code (527) Radio High-Line)
H4/10 Right front speaker
(with code (C08) Radio preinstallation including rod antenna (FFO) or
code (C50) smart radio 10 or
code (C57) smart radio 9 or
code (516) RADIO WITH USB INTERFACE or
code (527) Radio High-Line)
Modification notes
| Remove/install | ||
1 | Remove service flap | ||
2 | Remove left and right longitudinal member paneling | ||
3 | Partially loosen front CBS (2) to remove left and right door lining (5) | ||
4 | Remove door paneling | ||
5 | Carefully pull front CBS (2) away from vehicle, disconnect left door separation point (X35/1) or right door separation point (X35/2) and loosen retaining clip (1) from A-pillar | ||
6 | Mark installation position of quarter window (9), unscrew bolts (8) and detach quarter window (9) on door | Installation: Do not damage seal on quarter window (9) when installing. Otherwise it is necessary to replace the quarter window (9). | |
Installation: Before tightening bolts (8), align quarter window (9) according to markings made previously. | |||
| |||
| |||
7 | Unclip upper cover (3) from door lining (5) | Only loosen upper cover (3); it is still connected with the wiring harness (13). | |
8 | Unclip lower cover (4) on door lining (5) and remove | ||
9 | Remove spring washers (19) and remove hip protector (18) | For code (I53) Head/ thoraxbag | |
Installation: :Ensure that hip protector (18) is properly positioned in clip (20). Replace spring washers (19). Counterhold door paneling (5) when press on spring washers (19). Helper required. | |||
10 | Disconnect electrical connector (17) from right door CL motor (M14/5) or left door CL motor (M14/6) | ||
11.1 | Disconnect electrical connector (7) from left power window motor (M10/3) or right power window motor (M10/4) | On vehicles with code (V43) Power window | |
11.2 | Remove window crank | Vehicles without code (V43) Power window lifter | |
12 | Open door and unclip covering (10) in front area with assembly wedge (11) | Detach cover (10) only in lower area with assembly wedge (11) as shown. | |
Assembly wedge | |||
13 | Slide covering (10) toward front and guide out of door paneling (5) in rear area (arrow A) | ||
14 | Unscrew bolt (12) behind covering (10) | ||
15 | Remove expansion clip (6) | ||
16 | Unclip door trim (5) in lower area, slide upward and remove until cable (16) on inside door opener (14) is accessible | Installation: When installing door panel (5), do not pinch wiring harness (13). Otherwise it may be damaged. | |
Aid of helper required. | |||
Installation: Ensure that the impact protection (15) is positioned in its guide. | |||
17 | Unhook cable (16) from inside door opener (14) (arrow B) and then unhook (arrow C) | ||
18 | Remove door liner (5) | Aid of helper required. | |
19 | Install soundproofing (21) for left front speaker (H4/9) or right front speaker (H4/10) on door panel (5) | When replacing door panel (5) with code (C17) Sound package (2 tweeters, 2 bass reflex boxes and diplexer) (FFO). | |
20 | Install in the reverse order |
Front door
Number | Designation | Model 451.3/4 | |
BA72.10-P-1005-01H | Bolt, quarter window to upper door frame | Nm | 10 |
BA72.10-P-1006-01H | Bolt, quarter window to lower door frame | Nm | 10 |
Mounting wedge
110 589 03 59 00