P68.30-2875-09
1 Belt entrance paneling
2 Screw
A Cutting line
B Cutting line
3 Cutting blade
P68.30-2876-06
1 Belt entrance paneling
P68.30-2877-06
1 Belt entrance
2 Screw
| Remove | ||
1 | Remove closing plate for door beam | ||
2 | Remove seat console | ||
3 | Remove head collision pad | ||
4 | Remove spoiler from rollover bar | ||
5 | Unscrew bolts (2) | ||
6 | Mark cutting lines (A, B) along belt entrance paneling (1) | ||
7 | Cut belt entrance paneling (1) along marked cutting lines (A, B) with cutting blade (3) | Danger of damaging detachable body componentsObserve parts located below when cutting Proceed carefully to prevent damaging detachable body components.Cover or mask detachable body components to be reused. | |
8 | Carefully remove individual parts of the belt entrance paneling (1) from the body | ||
9 | Remove glue residues from body | ||
10 | Coat bare points on body with rust protection paint | ||
| Install | ||
11 | Clean belt entrance paneling (1) and prime at points to be glued. | Danger of damage from improper handling. Apply adhesive cleaner to non-visible surfaces. | |
12 | Apply glue on marked points (arrows) on belt entrance paneling (1) and fasten adhesive tape to edge (arrows) | Process glue within 25 min. before adhesive force of glue is negatively affected. The two application guns listed above can be used optionally. | |
Druckfix | |||
Pressfix | |||
Adhesive Sikaflex-254 booster | |||
13 | Apply glue at side of trunk cover at marked points (arrows) | Process glue within 25 min. before adhesive force of glue is negatively affected. The two application guns listed above can be used optionally. | |
Druckfix | |||
Pressfix | |||
Sikaflex-254 booster glue Sikaflex-254 booster | |||
14 | Mask edge of side wall with adhesive tape and apply glue at marked points (arrows) | Process glue within 25 min. before adhesive force of glue is negatively affected. The two application guns listed above can be used optionally. | |
Druckfix | |||
Pressfix | |||
Adhesive Sikaflex-254 booster | |||
15 | Insert belt entrance paneling (1) from rear, position and fasten with adhesive tape | Danger of damage from excessive glue. Ensure that glue does not come into contact with seatbelt. Ensure for corrects gaps, if necessary insert spacers. | |
16 | Drill 3 mm dia. hole and screw bolts (2) into B-pillar mount | ||
17 | Carefully remove adhesive tape and excessive glue from belt entrance paneling (1) | Observe correct gaps | |
18 | Install spoiler on rollover bar | ||
19 | Install head collision pad | ||
20 | Fill detachable body components | The two application guns listed above can be used optionally. | |
Druckfix | |||
Pressfix | |||
Sealing compound Durasil W15 2000 | |||
| General notes on filling detachable body components | ||
21 | Install seat console | ||
22 | Install closing plate for door beam |
Commercially available tools
Number | Designation | |
WH58.30-Z-1006-10A | Compressed air application gun for bag sealants | |
WH58.30-Z-1034-14A | Manual application gun for bag sealants |
Repair materials
Number | Designation | Order number |
BR00.45-Z-1057-01A | Sealing compound Durasil W15 2000 | Dow Corning GmbH |
BR00.45-Z-1076-02A | Adhesive Sikaflex-254 booster | Sika Deutschland GmbH |
BR00.45-Z-1041-04A | Sikaflex adhesive cleaner 205 | Sika Deutschland GmbH |
Powiązane dokumenty
- ah8800p100002cr Ogólne wskazówki dotyczące spajania elementów do zabudowy
- ar6800p0500cr
- ar7210p2505cr
- ar8800p1260cr
- ar9110p3000sm