Shown on left side of vehicle |
1 | Rear lamp reinforcement |
P63.20-9518-06
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | General information on body repair | ||
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
General information on MB materials | |||
| Remove | ||
1 | Remove detachable parts in area of repair point. | ||
2 | Cover all detachable parts remaining in vehicle with spark protection blankets. | ||
3 | Remove rear sidewall paneling lower section. | ||
4 | Remove rear lamp reinforcement (1). | ||
1K-zinc dust paint | |||
| Install | ||
Danger | The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases | Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system. | |
Topical note | Measures for preventing damage to components when performing electric welding and soldering work | ||
General information on riveting | |||
5 | Prepare rear lamp reinforcement (1). | ||
1K-zinc dust paint | |||
6 | Install rear lamp reinforcement (1). | ||
1K-zinc dust paint | |||
Blind rivet 6.412 (clamping range 1 mm to 3.5 mm, draw-off strength min. 15.5 kN) | |||
Blind rivet with countersunk head 6.414.0 (clamping range 1.5 mm to 3 mm, draw-off strength min. 15.5 kN) | |||
7 | Clean weld joints and sheet metal flange. | ||
8 | Install rear sidewall paneling lower section. | ||
9 | Remove spark protection blankets. | ||
10 | Reinstall detachable parts in area of repair point. |
Repair materials |
Number | Designation | Order number |
BR00.45-Z-1035-13A | Blind rivet 6.412 (clamping range 1 mm to 3.5 mm, draw-off strength min. 15.5 kN) | A 000 991 76 32 |
BR00.45-Z-1043-13A | Blind rivet with countersunk head 6.414.0 (clamping range 1.5 mm to 3 mm, draw-off strength min. 15.5 kN) | A 000 991 82 32 |
BR00.45-Z-1056-07A | 1K-zinc dust paint | A 000 986 28 00 |
Powiązane dokumenty
- ah5400p000101a Wskazówki dotyczące zapobiegania uszkodzeniom elementów elektronicznych na skutek rozładowania potencjału elektrostatycznego
- ah6000n000101a Ogólne wskazówki dotyczące napraw nadwozia
- ah6000p000102a Środki zapobiegające uszkodzeniom pojazdu lub jego elementów podczas spawania elektrycznego i lutowania
- ah6000p000301n Ogólne wskazówki dotyczące nitowania
- ah9800p940903a Informacje ogólne dotyczące środków MB
- ar6310p5665frx
- ar6320p201101frx
- ar6320p201102frx
- ar6320p201103frx
- as0000z000201a Niebezpieczeństwo zranienia skóry i oczy na skutek kontaktu z gorącymi lub żarzącymi się przedmiotami
- as0000z000701a Zagrożenie dla życia przez wysokie napięcie przy spawaniu elektrycznym. Niebezpieczeństwo wybuchu podczas spawania w pobliżu materiałów łatwopalnych. Niebezpieczeństwo urazu na skutek odprysków przy spawaniu oraz promieniowania u
- as0000z001701a Niebezpieczeństwo obrażeńo elementy pojazdu o ostrych krawędziach.