ar6320d110404ts

Install A-pillar inner section

Typ ar · temat 63.20 · wersja 0100 · 2018-03-28

Dotyczy: Model 907, 910

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 63 Ściana boczna › 63.20 Słupki — Seria 907 · Seria 910

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.45 Słupek — Seria 907 · Seria 910

AR63.20-D-1104-04TS

Install A-pillar inner section

Danger

The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases

Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system.

AS00.00-Z-0007-01A

Caution

Risk of injury caused by scraping or cutting body parts on sharp vehicle parts

Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.
Deburr repair panels.

AS00.00-Z-0017-01A

Topical note

Measures for preventing damage to vehicles or components when performing electric welding work

AH00.00-N-0005-01A

000 588 01 84 00 Welder

WS60.00-P-0021K

000 588 02 84 00 Welder

WS60.00-P-0022K

Model

907, 910

Install A-pillar inner section

907 589 01 23 00

Welding device

Repair materials

Number

Designation

Order number

BR00.45-Z-1107-01A

Black seam seal 300 ml

A 005 989 63 20

The next steps are shown on the left side of the vehicle for model 910.631 and must be similarly performed on the right side of the vehicle in the event of damage.

Install A-pillar inner section

D63.20-1496-08

1

Install, fit, and fix in place the center A-pillar inner section (1.2).

Use welding fixture.

2.1

Model 907
Center A-pillar inner section (1.2) (areas C1 and C2) (picture A).

2.2

Model 910
Center A-pillar inner section (1.2) (areas C1 and C2) (picture B).

3.1

Model 907
Center A-pillar inner section (1.2) (areas D1, D2 and D3) (picture A).

3.2

Model 910
Center A-pillar inner section (1.2) (areas D1, D2 and D3) (picture B).

4

Grind inert gas plug welds down flat (area D1).

5

Remove shavings.

Install A-pillar inner section

D63.20-1497-09

6

Install lower A-pillar inner section (1.3), fit, and fix in place.

7

Lower A-pillar inner section (1.3) (areas E1, E2, E3, E4, E5, F2, and F3).

8

A-pillar lower inner section (1.3) (areas H1 and H2).

Install A-pillar inner section

9

Sealant seal (area I).


D63.20-1499-01

Install A-pillar inner section

10

Install upper A-pillar inner section (1.1), fit, and fix in place.



11

Upper A-pillar inner section (1.1) (areas J, K, and L).



12

Upper A-pillar inner section (1.1) (area N).


D63.20-1498-06

Powiązane dokumenty