ar6320d009802tsc

Separate C-pillar paneling

Typ ar · temat 63.20 · wersja 0100 · 2018-10-05

Dotyczy: Model 907.6/7 with code T16 (Sliding door right) except code IR2 (Wheelbase 3250 mm) Right side of vehicle Model 907.6/7 with code T19 (Sliding door left) except code IR2 (Wheelbase 3250 mm) Left side of vehicle Model 910.623/633/643 with code T16 (Sliding door right) Right side of vehicle Model 910.623/633/643 with code T19 (Sliding door left) Left side of vehicle

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 63 Ściana boczna › 63.20 Słupki — Seria 907 (modele 6**, 7**) · Seria 910 (modele 623, 633, 643)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.45 Słupek — Seria 907 (modele 6**, 7**) · Seria 910 (modele 623, 633, 643)

AR63.20-D-0098-02TSC

Separate C-pillar paneling

Model

907.6/7

with code T16 (Sliding door right)

except code IR2 (Wheelbase 3250 mm)

Right side of vehicle

Model

907.6/7

with code T19 (Sliding door left)

except code IR2 (Wheelbase 3250 mm)

Left side of vehicle

Model

910.623/633/643

with code T16 (Sliding door right)

Right side of vehicle

Model

910.623/633/643

with code T19 (Sliding door left)

Left side of vehicle

Repair materials

Number

Designation

Order number

BR00.45-Z-1056-07A

1K-zinc dust paint

A 000 986 28 00

Additional information can be found in the superordinate service document.

The safety information in the superordinate service document must be observed.

The next steps are shown on model 907.633 with code T16 (right sliding door) on the right side of the vehicle and must be carried out in the same way for vehicles with code T19 (left sliding door) on the left side of the vehicle in the event of damage.

Separate C-pillar paneling

1

Mark separating line on outer sliding door entrance (2) (area A).


Observe dimension (A).



2

Cut outer sliding door entrance (2) at separating point (area A).


Do not cut too deeply.
This prevents damage to the component parts located underneath.


Commercially available devices/tools
Body power jigsaw


a

Dimension (approx. 165 mm)

D63.20-A002-06

Separate C-pillar paneling

3

Expose spot welds at C-pillar paneling (1) (areas C1 and D).


Commercially available devices/tools
Rotary wire brush



4

Cut off spot welds at C-pillar paneling (1) (areas C1 and D).


Cut off spot weld through 2 panel thicknesses (area D).


Commercially available devices/tools
Spot weld milling machine


D63.20-A003-11

Separate C-pillar paneling

5

Expose spot welds at C-pillar paneling (1) (areas E and E1).


Commercially available devices/tools
Rotary wire brush



6

Cut off spot welds at C-pillar paneling (1) (areas E and E1).


Cut off spot welds through 2 panel thicknesses (area E1).


Commercially available devices/tools
Spot weld milling machine


D63.20-A004-12

Separate C-pillar paneling

7

Expose spot welds at C-pillar paneling (1) (areas F, G and H).


Commercially available devices/tools
Rotary wire brush



8

Cut off spot welds at C-pillar paneling (1) (areas F, G and H).


Commercially available devices/tools
Spot weld milling machine



9

Heat adhesive in hatched area and cut.



10

Remove damaged C-pillar paneling (1).


D63.20-A005-06

Separate C-pillar paneling

11

Grind mating surfaces down to bare metal in cross-hatched areas and around holes.


Commercially available devices/tools
Rotary wire brush



12

Level adhesive residues in hatched areas to 1 mm.



13

Remove shavings and milling chips.


Commercially available devices/tools
Wet and dry vacuum cleaner



14

Zinc dust paint to insides of spot weld flanges.


D63.20-A006-06