ar6320d009802ts

Separate C-pillar paneling

Typ ar · temat 63.20 · wersja 0100 · 2018-10-08

Dotyczy: Model 907.6/7 with code IR2 (Wheelbase 3250 mm) with code T16 (Sliding door right) Right side of vehicle Model 907.6/7 with code IR2 (Wheelbase 3250 mm) with code T19 (Sliding door left) Left side of vehicle Model 910.621/631/641 with code T16 (Sliding door right) Right side of vehicle Model 910.621/631/641 with code T19 (Sliding door left) Left side of vehicle

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 63 Ściana boczna › 63.20 Słupki — Seria 907 (modele 6**, 7**) · Seria 910 (modele 621, 631, 641)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.45 Słupek — Seria 907 (modele 6**, 7**) · Seria 910 (modele 621, 631, 641)

AR63.20-D-0098-02TS

Separate C-pillar paneling

Model

907.6/7

with code IR2 (Wheelbase 3250 mm)

with code T16 (Sliding door right)

Right side of vehicle

Model

907.6/7

with code IR2 (Wheelbase 3250 mm)

with code T19 (Sliding door left)

Left side of vehicle

Model

910.621/631/641

with code T16 (Sliding door right)

Right side of vehicle

Model

910.621/631/641

with code T19 (Sliding door left)

Left side of vehicle

Repair materials

Number

Designation

Order number

BR00.45-Z-1056-07A

1K-zinc dust paint

A 000 986 28 00

Additional information can be found in the superordinate service document.

The safety information in the superordinate service document must be observed.

The next steps are shown on model 907.6 with code T16 (right sliding door) on the right side of the vehicle and must be performed in the same way on vehicles with code T19 (left sliding door) in the event of damage to the left side of the vehicle.

Separate C-pillar paneling

1

Mark separation line on outer sliding door entrance (2) (area A).


Observe dimension (A).



2

Cut outer sliding door entrance (2) at separating point (area A).


Do not cut too deeply.
This prevents damage to the component parts located underneath.


Commercially available devices/tools
Body power jigsaw


Shown on model 907.633

a

Dimension (approx. 165 mm)

D63.20-A002-06

Separate C-pillar paneling

3

Expose spot welds on C-pillar paneling (1) (area C1).


Commercially available devices/tools
Rotary wire brush



4

Cut off spot welds on C-pillar paneling (1) (area C1).


Commercially available devices/tools
Spot weld milling machine


Shown on model 907.633

D63.20-A003-11

Separate C-pillar paneling

5

Expose spot welds on C-pillar paneling (1) (area E1).


Commercially available devices/tools
Rotary wire brush



6

Cut off spot welds on C-pillar paneling (1) (area E1).


Cut off spot welds through 2 panel thicknesses (area E1).


Commercially available devices/tools
Spot weld milling machine


Shown on model 907.633

D63.20-A004-12

Separate C-pillar paneling

D63.20-A013-09

Shown on model 907.631

7

Expose spot welds on C-pillar paneling (1) (areas F, G, H, and I).

Commercially available devices/tools
Rotary wire brush

8

Cut off spot welds on C-pillar paneling (1) (areas F, G, H, and I).

Cut off spot welds (area I) through 2 panel thicknesses.

Commercially available devices/tools
Spot weld milling machine

9

Heat adhesive in hatched areas and separate.

10

Remove damaged C-pillar paneling (1).

Separate C-pillar paneling

D63.20-A014-09

Shown on model 907.631

11

Grind mating surfaces down to bare metal in cross-hatched areas and around holes.

Commercially available devices/tools
Rotary wire brush

12

Level adhesive residues in hatched areas to 1 mm.

13

Remove shavings and milling chips.

Commercially available devices/tools
Wet and dry vacuum cleaner

14

Zinc dust paint to insides of spot weld flanges.