Model | 447.605 |
with code T19 (Sliding door left) | |
with code W29 (Window fixed behind) | |
Left side of vehicle | |
Model | 447.605 |
with code W29 (Window fixed behind) | |
Right side of vehicle | |
Model | 447.705 |
with code T19 (Sliding door left) | |
with code W29 (Window fixed behind) | |
with code ZK4 (Mixto) | |
Left side of vehicle | |
Model | 447.705 |
with code W29 (Window fixed behind) | |
with code ZK4 (Mixto) | |
Right side of vehicle | |
Model | 447.815 |
Right side of vehicle | |
Model | 447.815 |
with code T19 (Sliding door left) | |
Left side of vehicle | |
Model | 448.705 |
with code T19 (Sliding door left) | |
with code W29 (Window fixed behind) | |
Left side of vehicle | |
Model | 448.705 |
with code W29 (Window fixed behind) | |
Right side of vehicle | |
Model | 448.815 |
Right side of vehicle | |
Model | 448.815 |
with code T19 (Sliding door left) | |
Left side of vehicle |
Gap dimensions |
Number | Designation | Model 447, 448 except code W65, W68 | Model 447, 448 with code W65, model 447, 448 with code W68 | |||
BE60.00-N-1006-01J | Gap dimensions | Sliding door to roof frame | Dimension "FA" | mm | 4,5 (1,4) | 4,5 (1,4) |
Sliding door to sidewall | Dimension "FB" | mm | 4 (+1,2/-0,8) | 4 (+1,2/-0,8) | ||
Glass pane in sliding door, all-round | Dimension "FC" | mm | 3 | 3 | ||
For picture, see | ||||||
Gap dimensions |
Number | Designation | Model 447, 448 except code W65, W68 | Model 447, 448 with code W65, model 447, 448 with code W68 | |||
BE60.00-N-1007-01J | Gap dimensions | Sidewall to liftgate | Dimension "GA" | mm | - | 4,5 (+1,5/-0,2) |
Sidewall to cover on guide rail of sliding door | Dimension "GB" | mm | 1,5 (0,8) | 1,5 (0,8) | ||
Sidewall to fuel filler door | Dimension "GC" | mm | 4,5 (1) | 4,5 (1) | ||
Glass pane in sidewall at front, all-round | Dimension "GD" | mm | 3 | 3 | ||
Sidewall to taillamp | Dimension "GE" | mm | 1,2 (0,5) | 1,2 (0,5) | ||
Glass pane in sidewall at rear, all-round | Dimension "GF" | mm | 3 | 3 | ||
For picture, see | ||||||
Gap dimensions |
Number | Designation | Model 447, 448 except code W65, W68 | Model 447, 448 with code W65, model 447, 448 with code W68 | |||
BE60.00-N-1008-01J | Gap dimensions | Rear window in liftgate, all-round | Dimension "HA" | mm | - | 4 (1) |
Folding rear window in liftgate, all-round | Dimension "HB" | mm | - | 4 (1) | ||
Liftgate to taillamp | Dimension "HC" | mm | - | 4,5 (1) | ||
Liftgate to bumper at side | Dimension "HD" | mm | - | 4 (1) | ||
Liftgate to bumper at bottom | Dimension "HE" | mm | - | 6 (1,5) | ||
Liftgate to roof frame | Dimension "HF" | mm | - | 5,5 (1) | ||
For picture, see | - | |||||
Gap dimensions |
Number | Designation | Model 447, 448 except code W65, W68 | Model 447, 448 with code W65, model 447, 448 with code W68 | |||
BE60.00-N-1009-01J | Gap dimensions | Left rear-end door to right rear-end door | Dimension "IA" | mm | 6 (1) | - |
Rear-end door to bumper at side | Dimension "IB" | mm | 4,5 (1) | - | ||
Rear-end door to bumper at bottom | Dimension "IC" | mm | 6 (1,5) | - | ||
Rear-end door to taillamp | Dimension "ID" | mm | 6,4 (1) | - | ||
Rear-end door to cover over taillamp | Dimension "IE" | mm | 6,4 (1) | - | ||
Rear-end door to roof frame | Dimension "IF" | mm | 7 (1,5) | - | ||
Rear window in rear-end door, all-round | Dimension "IG" | mm | 4 (1) | - | ||
For picture, see | - | |||||
129 589 03 21 00
Feeler gauge
The following steps are shown on the left side of the vehicle and must be accomplished analogously on the right side in the event of damage.
1 | Install side wall paneling (1), sliding door, liftgate or rear-end door, seal and lock striker and fit. |
2 | Check gaps using feeler gauge and adjust. |
3 | Fix sidewall paneling (1) in place. |
4 | Remove sliding door, liftgate or rear-end door, seal and lock striker. |
S63.10-5871-06
5 | Drill Ø 7.1 mm rivet holes in side wall paneling (1) at defined punch marks (area A). |
6 | Remove side wall paneling (1). |
7 | Deburr rivet hole on both sides. |
8 | Coat insides of riveted joint with zinc dust paint. |
S63.10-5872-09
9 | Apply sealant to body. |
10 | Apply sealant to lock striker reinforcement (2) (area D). |
11 | Apply 2-component adhesive to body (areas B and C). |
Observe pretreatment of bonding surfaces (areas B and C). Refer to the manufacturer's information for the curing and working times of 2-component adhesive. |
S63.10-5873-09
12 | Install side wall paneling (1) and fit. |
13 | Fix sidewall paneling (1) in place. |
14 | Side wall paneling (1) (areas E to H). |
15 | Drill side wall paneling (1) before inert gas welding (arrows). |
16 | Side wall paneling (1) (areas K to M). |
17 | Side wall paneling (1) (areas I and J). |
Inert gas weld in intervals and allow to cool down in between. Reduces heat distortion. |
S63.10-5874-09
18 | Side wall paneling (1) (areas N and O). |
19 | Grind inert gas welds and inert gas spot welds down flat. |
20 | Clean weld joints. |
21 | Restore and smooth surfaces on side wall paneling (1). |
22 | Remove shavings and drill chips. |
23 | Install blind rivet nut M5 (area P). |