ar6310s012601ea

Cut off sidewall paneling with window cutout

Typ ar · temat 63.10 · wersja 0100 · 2016-02-11

Dotyczy: Model 447.601 with code T19 (Sliding door left) with code W29 (Window fixed behind) Left side of vehicle Model 447.601 with code W29 (Window fixed behind) Right side of vehicle Model 447.701 with code T19 (Sliding door left) with code W29 (Window fixed behind) with code ZK4 (Mixto) Left side of vehicle Model 447.701 with code W29 (Window fixed behind) with code ZK4 (Mixto) Right side of vehicle Model 447.811 Right side of vehicle Model 447.811 with code T19 (Sliding door left) Left side of vehicle

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 63 Ściana boczna › 63.10 Ściana boczna — Seria 447 (modele 601, 701, 811)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.35 Błotnik/ ściana boczna — Seria 447 (modele 601, 701, 811)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.38 Poszycie z lewej strony — Seria 447 (modele 601, 701, 811)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.39 Poszycie z prawej strony — Seria 447 (modele 601, 701, 811)

AR63.10-S-0126-01EA

Cut off sidewall paneling with window cutout

Model

447.601

with code T19 (Sliding door left)

with code W29 (Window fixed behind)

Left side of vehicle

Model

447.601

with code W29 (Window fixed behind)

Right side of vehicle

Model

447.701

with code T19 (Sliding door left)

with code W29 (Window fixed behind)

with code ZK4 (Mixto)

Left side of vehicle

Model

447.701

with code W29 (Window fixed behind)

with code ZK4 (Mixto)

Right side of vehicle

Model

447.811

Right side of vehicle

Model

447.811

with code T19 (Sliding door left)

Left side of vehicle

The following steps are shown on the left side of the vehicle and must be accomplished analogously on the right side in the event of damage.

Cut off sidewall paneling with window cutout

S63.10-5747-09

x

Dimension approx. 15 mm

1

Mark separating point on side wall paneling (1) and cut (area A).

Do not cut too deeply.
Otherwise the components below can be damaged and weakened.

2

Expose spot welds on side wall paneling (1) and cut out (areas B to G).

Cut out spot welds (arrows) through two panel thicknesses.

Cut off sidewall paneling with window cutout

S63.10-5748-09

3

Expose spot weld and drill through (area H).

4

Expose spot weld on side wall paneling (1) and cut out (area I).

Cut off sidewall paneling with window cutout

S63.10-5749-09

5

Expose spot welds on rear side wall paneling bottom section (4) and cut out (areas J to M).

6

Expose MAG spot welds on rear side wall paneling bottom section (4) and cut out (area N).

7

Separate inert gas weld on rear side wall paneling bottom section (4) (area O).

8

Heat sidewall paneling (1) in crosshatched areas.

Cross-hatched areas are bonded with adhesive.

9

Remove damaged side wall paneling (1).

Cut off sidewall paneling with window cutout

10

Sand down mating surfaces to bare metal in cross-hatched areas.



11

Remove shavings and drill chips.



12

Coat insides of spot weld flanges with zinc dust paint.


Do not coat bonding surfaces with zinc dust paint (areas P and Q).
Otherwise there may be adhesion problems.


Observe pretreatment of bonding surfaces (areas P and Q).


S63.10-5750-06

Cut off sidewall paneling with window cutout

13

Grind mating surfaces down to bare metal in crosshatched areas and around hole (area R).


Sand down spot weld flanges to bare metal on both sides.



14

Remove shavings and drill chips.



15

Coat insides of spot weld flanges with zinc dust paint.


S63.10-5751-06