ar6310s011005ea

Remove side wall paneling

Typ ar · temat 63.10 · wersja 0102 · 2017-04-03

Dotyczy: Model 447.601 except code W29 (Window fixed behind) Right side of vehicle Model 447.601 with code T19 (Sliding door left) except code W29 (Window fixed behind) Left side of vehicle Model 447.701 except code W29 (Window fixed behind) except code W32 (Ausstellfenster Fahrgastraum hinten elektrisch) Right side of vehicle Model 447.701 with code T19 (Sliding door left) except code W29 (Window fixed behind) except code W32 (Ausstellfenster Fahrgastraum hinten elektrisch) Left side of vehicle

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 63 Ściana boczna › 63.10 Ściana boczna — Seria 447 (modele 601, 701)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.35 Błotnik/ ściana boczna — Seria 447 (modele 601, 701)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.38 Poszycie z lewej strony — Seria 447 (modele 601, 701)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.39 Poszycie z prawej strony — Seria 447 (modele 601, 701)

AR63.10-S-0110-05EA

Remove side wall paneling

Model

447.601

except code W29 (Window fixed behind)

Right side of vehicle

Model

447.601

with code T19 (Sliding door left)

except code W29 (Window fixed behind)

Left side of vehicle

Model

447.701

except code W29 (Window fixed behind)

except code W32 (Ausstellfenster Fahrgastraum hinten elektrisch)

Right side of vehicle

Model

447.701

with code T19 (Sliding door left)

except code W29 (Window fixed behind)

except code W32 (Ausstellfenster Fahrgastraum hinten elektrisch)

Left side of vehicle

The following steps are shown on the left side of the vehicle and must be accomplished analogously on the right side in the event of damage.

Remove side wall paneling

S63.10-6116-09

x

Dimension approx. 15 mm

1

Mark separating point on side wall paneling (1) and cut (area A).

Do not cut too deeply.
Otherwise the components below can be damaged and weakened.

2

Expose spot welds on side wall paneling (1) and cut out (areas B, D bis G).

Cut out spot welds (arrows) through two panel thicknesses.

Remove side wall paneling

3

Expose spot weld and drill through (area H).



4

Expose spot weld on side wall paneling (1) and cut out (area I).


S63.10-6117-06

Remove side wall paneling

S63.10-6118-09

5

Expose spot welds on rear side wall paneling bottom section (4) and cut out (areas J to M).

6

Expose MAG spot welds on rear side wall paneling bottom section (4) and cut out (area N).

7

Separate inert gas weld on rear side wall paneling bottom section (4) (area O).

8

Heat sidewall paneling (1) in crosshatched areas.

Cross-hatched areas are bonded.

9

Remove damaged side wall paneling (1).

Remove side wall paneling

10

Grind mating surfaces down to bare metal in the cross-hatched inner C-pillar sidewall .


Sand down spot weld flanges to bare metal on both sides.



11

Remove shavings and drill chips.



12

Coat insides of spot weld flanges with zinc dust paint.


Do not coat bonding surfaces with zinc dust paint (areas P and Q).
Otherwise there may be adhesion problems.


Observe preatreatment of bonding surfaces (areas P and Q).


S63.10-6119-06

Remove side wall paneling

13

Grind mating surfaces down to bare metal in crosshatched areas and around hole (area R).


Sand down spot weld flanges to bare metal on both sides.



14

Remove shavings and drill chips.



15

Coat insides of spot weld flanges with zinc dust paint.


S63.10-6120-06