Weld in right side wall paneling up to window cutout · ar6310d589204fa · Mercedes-Benz WIS

AR63.10-D-5892-04FA	Weld in right side wall paneling up to window cutout
 Danger	The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases	Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system.	AS00.00-Z-0007-01A
 Warning	Risk of injury. Skin or eye injuries may result when handling hot or glowing objects.	Wear protective gloves, protective clothing and safety glasses, if necessary.	AS00.00-Z-0002-01A
 Caution	Risk of injury caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
Topical note	Measures for preventing damage to vehicles or components when performing electric welding work		AH00.00-N-0005-01A
Topical note	General information on body repair		AH60.00-N-0001-01A

Model	909.843
	with code T16 (Sliding door right)
	except code W03 (Body extension)

Repair materials

Number	Designation	Order number
BR00.45-Z-1003-01A	White sealing compound, 310 ml, DBL 6069.20	A 001 989 63 20

1	Apply sealant to side wall reinforcements (3).

2	Install side wall paneling (1), fit and fix in place.

D63.10-0065-06

3	Side wall paneling (1)   (areas A, B and C).

 Counterhold steel and copper block (approx. 25 mm x 25 mm x 200 mm) from outside.
Otherwise the sheet steel parts can distort.

D63.10-1888-06

4	Sidewall paneling (1)   (area D).

5	Side wall paneling (1)   (area E).

 Inert gas weld in intervals and allow welding area to cool down in between. This reduces heat distortion.

D63.10-1889-06

6	Side wall paneling (1)   (areas K).

 Counterhold steel and copper block (approx. 25 mm x 25 mm x 200 mm) from outside.
Otherwise the sheet steel parts can distort.

7	Sidewall paneling (1)   (Area J).

D63.10-1890-12

8	Side wall paneling (1)   (area G).

D63.10-1872-01

9	Sidewall paneling (1)  (Area H).

D63.10-1873-01

10	Cut side wall paneling (1) along window cutout of side wall inner section (10) (area N).

11	Deburr cutting edge.

12	Grind inert gas welds down flat.

13	Restore surface and smooth.

14	Remove grinding dust.

D63.10-1891-12

ah0000n000501a Zabezpieczenia zapobiegające uszkodzeniom pojazdu lub jego elementów podczas spawania elektrycznego
ah6000n000101a Ogólne wskazówki dotyczące napraw nadwozia
as0000z000201a Niebezpieczeństwo zranienia skóry i oczy na skutek kontaktu z gorącymi lub żarzącymi się przedmiotami
as0000z000701a Zagrożenie dla życia przez wysokie napięcie przy spawaniu elektrycznym. Niebezpieczeństwo wybuchu podczas spawania w pobliżu materiałów łatwopalnych. Niebezpieczeństwo urazu na skutek odprysków przy spawaniu oraz promieniowania u
as0000z001701a Niebezpieczeństwo obrażeńo elementy pojazdu o ostrych krawędziach.