ar6310d004002ts

Prepare inner section of rear side wall paneling up to window cutout for installation

Typ ar · temat 63.10 · wersja 0100 · 2019-02-19

Dotyczy: Model 907.6 with code W22 (Fixed window, center left) with code W23 (Fixed window, center right) Model 907.6 with code W24 (Sliding window center left) with code W25 (Sliding window center right) Model 907.6 with code W27 (Fixed window, rear left) with code W28 (Fixed window at rear right) Model 907.6 with code W34 (Sliding window rear left) with code W35 (Sliding window rear right) Model 907.7

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 63 Ściana boczna › 63.10 Ściana boczna — Seria 907 (modele 6**, 7**)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.35 Błotnik/ ściana boczna — Seria 907 (modele 6**, 7**)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.38 Poszycie z lewej strony — Seria 907 (modele 6**, 7**)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.39 Poszycie z prawej strony — Seria 907 (modele 6**, 7**)

AR63.10-D-0040-02TS

Prepare inner section of rear side wall paneling up to window cutout for installation

Model

907.6

with code W22 (Fixed window, center left)

with code W23 (Fixed window, center right)

Model

907.6

with code W24 (Sliding window center left)

with code W25 (Sliding window center right)

Model

907.6

with code W27 (Fixed window, rear left)

with code W28 (Fixed window at rear right)

Model

907.6

with code W34 (Sliding window rear left)

with code W35 (Sliding window rear right)

Model

907.7

Repair materials

Number

Designation

Order number

BR00.45-Z-1056-07A

1K-zinc dust paint

A 000 986 28 00

Additional information can be found in the superordinate service document.

The safety information in the superordinate service document must be observed.

The next steps are shown on the left component parts on model 907.633 and must be performed in a similar manner on vehicles with damage on the right side of the vehicle.

Prepare inner section of rear side wall paneling up to window cutout for installation

1

Mark separating points on inside part of sidewall (1.1) (areas A, A1, B and B1).


Transfer separation lines from vehicle.



2

Cut separating points on inside part of sidewall (1.1) (areas A, A1, B and B1).


Commercially available devices/tools
Body power jigsaw



3

Dispose of upper remaining section of inside part of sidewall (1.1).


D63.10-A026-12

Prepare inner section of rear side wall paneling up to window cutout for installation

D63.10-A025-09

4

Punch holes in reinforcement (2) (area E), reinforcement (3) (area F) and in new inside part of sidewall (1) (areas C and D) with Ø 6 mm.

Commercially available devices/tools
Hole punching pliers 6 mm

5

Grind mating surfaces down to bare metal in cross-hatched areas and around holes at reinforcement (2) (area E), reinforcement (3) (area F) and new inside part of sidewall (1) (areas C and D).

Sand down spot weld flanges to bare metal on both sides.

Commercially available devices/tools
Rotary wire brush

6

Remove shavings.

Commercially available devices/tools
Wet and dry vacuum cleaner

7

Zinc dust paint to insides of spot weld flanges.