D72.16-1357-09
1 | Release for electric drive (except code T63 (Release of electric sliding door(s))) | 7 | Protective foil | |
2 | Exterior emergency release unit (with code T63 (Release of electric sliding door(s))) | X100/2 | HLS/right sliding door connector | |
3 | Lever (with code T63 (Release of electric sliding door(s))) | X100/13 | Right sliding door connector | |
4 | Bracket | X100/23 | Right sliding door connector (4-pin) | |
5 | Bottom carriage | X100/24 | Right sliding door connector (2-pin) | |
6 | Energy chain | X100/27 | Right sliding door connector (2-pin) |
Danger ! | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
| Remove | ||
1 | Remove bottom door trim | ||
2.1 | Turn release for electric drive (1) 180° clockwise to "MAN" position using key | MODEL 900.6 except CODE T63 (Release for electric sliding door(s)) | |
The motor coupling for electrical actuation of the sliding door is released. | |||
2.2 | Actuate lever (3) of exterior emergency release unit (2) | MODEL 900.6 with CODE T63 (Release for electric sliding door(s)) | |
The retainer must engage. | |||
The motor coupling for electrical actuation of the sliding door is released. | |||
3 | Disconnect right sliding door connector (X100/13), right 4-pin sliding door connector (X100/23) and right 2-pin sliding door connector (X100/24) | ||
4 | Remove lower guide rail | ||
5 | Disconnect right MWH/sliding door connector (X100/2) and right 2-pin sliding door connector (X100/27) | ||
6 | Create access to wiring harness in entrance | ||
7 | Unclip energy chain (6) from sectional molding of protective foil (7) | ||
8 | Detach bracket (4) with lower carriage (5) from sliding door | ||
| Install | ||
9 | Attach bracket (4) with lower carriage (5) to sliding door | ||
10 | Clip energy chain (6) onto sectional molding of protective foil (7) | Do not grease the energy chain (6). | |
11 | Secure wiring harness in entrance | ||
12 | Connect right MWH/sliding door connector (X100/2) and right 2-pin sliding door connector (X100/27) | ||
13 | Install bottom guide rail | ||
14 | Connect right sliding door connector (X100/13), right 4-pin sliding door connector (X100/23) and right 2-pin sliding door connector (X100/24) | ||
15 | Install lower door trim | ||
Adjust | |||
16 | Adjust lower carriage (5) | MODEL 900.6 | |
Bolt, lower carriage to sliding door | |||
17.1 | Turn release for electric drive (1) 180° counterclockwise to "AUTO" position using key | MODEL 900.6 except CODE T63 (Release for electric sliding door(s)) | |
The motor coupling for electrical actuation of the sliding door is locked. | |||
17.2 | Move lever (3) of exterior emergency release unit (2) back to starting position | MODEL 900.6 with CODE T63 (Release for electric sliding door(s)) | |
The motor coupling for electrical actuation of the sliding door is locked. | |||
Learn in electric sliding door | |||
18 | Completely open sliding door using switch on center console or on B-pillar panel and close again |
Powiązane dokumenty
- ar7216d102302i Regulacja równoległości, głębokości montażowej i ogranicznika drzwi przesuwnych
- ar7216d6610g Demontaż i montaż okładziny drzwi przesuwnych
- ar7216d7816a Demontaż i montaż prowadnicy drzwi przesuwnych dolnej
- as0000z001101a Niebezpieczeństwo zranienia przez zakleszczenie lub zmiażdżenie palców podczas demontażu, montażu i prac regulacyjnych przy pokrywach, drzwiach i oknie dachowym.