Remove/install bearing for rear axle differential suspension in rear axle carrier at left front · ar3510p005602mfc · Mercedes-Benz WIS

AR35.10-P-0056-02MFC

Remove/install bearing for rear axle differential suspension in rear axle carrier at left front

Model	118, 177, 247 with engine 139, 260, 282, 654
	with code M005 (Vehicles with 4MATIC/all-wheel drive)

652 589 00 33 21

Hand pump

176 589 00 43 00

Extraction and insertion tool

001 589 51 33 00

Hollow piston cylinder

652 589 00 33 23

Hydraulic hose (complete)

Repair materials

Number	Designation	Order number
BR00.45-Z-1097-06A	Mobil Vacuoline 137 insertion agent, 0.5 l	A 000 989 18 60 09

P35.31-2288-09

Shown on model 177

02	Counterholder	021	Hydraulic hose
04	Thrust piece	022	Hand pump
06	Installation ring	1	Bearing
09	Nut	2	Rear axle carrier
020	Hollow-piston cylinder	10	Spindle

Remove

 Required special tools:

  Hollow-piston cylinder (020) 001 589 51 33 00

  Hydraulic hose (021) 652 589 00 33 23

  Hand pump (022) 652 589 00 33 21

The following tools are required from the  extraction and insertion tool 176 589 00 43 00:

  Counterholder (02) 176 589 00 43 02

  Thrust piece (04) 176 589 00 43 04

  Nut (09) 176 589 00 43 09

  Spindle (10) 176 589 00 43 10

1	Mount  hollow-piston cylinder (020) with  hydraulic hose (021) onto  hand pump (022).

2	Insert  counterholder (02) from rear into rear axle carrier (2).

  When removing, the installation ring (06) must not be attached to the  counterholder (02).
The arrow on the  counterholder (02) must point downward.

3	 Position spindle (10),  nut (09),  hollow-piston cylinder (020) and  thrust piece (04), as shown, onto bearing (1) and  the counterholder (02).

4	Press bearing (1) rearward out of the rear axle carrier (2).

 If the  hollow-piston cylinder (020) reaches its maximum stroke, release pressure at  hand pump (022) and retighten  nut (09). Then repeat the press-out procedure.

5	 Remove spindle (10),  nut (09),  hollow-piston cylinder (020),  thrust piece (04) and the bearing (1).

6	Remove  counterholder (02) from rear axle carrier (2).

P35.31-2289-09

Shown on model 177

02	Counterholder	021	Hydraulic hose
04	Thrust piece	022	Hand pump
06	Installation ring	1	Bearing
09	Nut	2	Rear axle carrier
020	Hollow-piston cylinder	10	Spindle

Install

 Required special tools:

  Hollow-piston cylinder (020) 001 589 51 33 00

  Hydraulic hose (021) 652 589 00 33 23

  Hand pump (022) 652 589 00 33 21

The following tools are required from the  extraction and insertion tool 176 589 00 43 00:

  Counterholder (02) 176 589 00 43 02

  Thrust piece (04) 176 589 00 43 04

  Installation ring (06) 176 589 00 43 06

  Nut (09) 176 589 00 43 09

  Spindle (10) 176 589 00 43 10

7	 Insert installation ring (06) into  counterholder (02) and engage.

  Installation ring (06) determines the end position of the bearing (1) in the rear axle carrier (2).

8	Insert  counterholder (02) with  installation ring (06) from rear into rear axle carrier (2).

 The arrow on the  counterholder (02) must point downward.

9	Apply insertion agent to bearing (1).

10	 Position spindle (10),  nut (09), den  hollow-piston cylinder (020), bearing (1) and  thrust piece (04), as shown, onto rear axle carrier (2) and  counterholder (02).

 The protrusion of bearing (1) must face forward.

11	Press bearing (1) rearward into rear axle carrier (2).

 If the  hollow-piston cylinder (020) reaches its maximum stroke, release pressure at  hand pump (022), and retighten  nut (09). Then repeat the press-in procedure.

12	 Remove spindle (10),  nut (09),  hollow-piston cylinder (020) and  thrust piece (04).

13	Remove  counterholder (02) with  installation ring (06) from rear axle carrier (2).

14	Wipe off excess insertion agent.