ar3222p8100tx

Check AIRmatic for leaks

Typ ar · temat 32.22 · wersja 0104 · 2012-05-09

Dotyczy: MODEL 219.3 with CODE (489) AIRmatic (semi-active air suspension)

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 2 Podwozie › 32 Zawieszenie › 32.22 Zawieszenie pneumatyczne — Seria 219 (modele 3**)

EinPAS 20 Zawieszenie › 20.16 Zawieszenie › 20.16.1 Informacje podstawowe — Seria 219 (modele 3**)

AR32.22-P-8100TX

Check AIRmatic for leaks

3.5.12

MODEL 219.3 with CODE (489) AIRmatic (semi-active air suspension)

Check AIRmatic for leaks

P32.22-2316-09

1 Pressure line connection

2 Rear axle distributor

40 Suspension struts, front

40a Pressure line connections

41 Air suspensions

41 A Pressure line connections

41p Additional volume reservoir

RA pressure line fitting on rear axle distributor

P Pressure line connection to AIRmatic compressor unit

SP Pressure line fitting on central reservoir

VL Pressure line connection to left front suspension strut

FR Pressure line connection to right front suspension strut

42 Central reservoir

42a Pressure line connection

A9/1 AIRmatic compressor unit

Y36/6 AIRmatic central reservoir charge valve

Check AIRmatic for leaks

P32.22-2317-06

3 Rear seat cushion

4 Pressure line connector

5 Felt casing

6 Pressure lines

Remove/install

Notes on AIRmatic

AH32.22-P-1000-02T

Wait for approx. 10 to 15 min. after spraying the pressure line connections with leak detection spray. This allows smaller leaks to be detected (bubbles form). Larger leaks are visible immediately

1

Remove rear seat cushion (3)

AR91.12-P-1020TX

2

Remove right side trunk lining

AR68.30-P-4800TX

3.1

Remove front section of lower engine compartment paneling

Vehicles with gasoline engine

AR61.20-P-1105TX

3.2

Remove front section of bottom section of soundproofing

Vehicles with diesel engine

AR94.30-P-5300TX

4

Remove front section of fender liner in left front fender

AR88.10-P-1310TX

Checking

5

Remove felt wrapping (5) from pressure line connector (4) and check if pressure lines (6) are inserted up to markings (arrows) in pressure line connector (4)

Installation: After completing leakage test, reinstall felt wrapping (5) .

6

Spray leak detection spray onto pressurized line connection fitting (4)

Leak detection spray

*BR00.45-Z-1002-03A

for USA

*BR00.45-Z-1004-03A

If pressure line connector (4) is defective:

Repair AIRmatic compressed-air line.

AR32.22-P-2001-02TX

7

Use leakage spray on pressure line terminals on AIRmatic central reservoir charge valve (Y36/6), pressure line (1) on AIRmatic compressor unit (A9/1) and pressure line terminal (42a) on central reservoir (42)

If pressurized line connection fitting is defective:

Repair AIRmatic compressed-air line.

AR32.22-P-2001-02TX

8

Apply leakage spray to sealing compound area around the pressure line terminal (40a) front suspension strut (40), the pressure line terminal (41a) on the air springs (41) and on the rear axle hub (2)

If pressurized line connection fitting is defective:

Repair AIRmatic compressed-air line.

AR32.22-P-2001-02TX

9

Install in the reverse order

Repair materials

Number

Designation

Order number

BR00.45-Z-1002-03A

Leak detection spray

Christof Fischer GmbH,
Augsburger Str. 289-293,
70327 Stuttgart
Germany
Tel. +49 711 30502-0
Fax +49 711 30502-10
www.kaeltefischer.de

BR00.45-Z-1004-03A

Leakage spray for USA

LIQUI MOLY
Gary Boyd
1820 Clark Avenue

Long Beach, CA 90815
USA
Tel. +1 562 5975519

Fax + 1 562 5975269
www.liqui-moly.com

Powiązane dokumenty