ar1440b2057a

Remove/install pressure limiting valve of pump module

Typ ar · temat 14.40 · wersja 0103 · 2019-07-24

Dotyczy: Engine 457.9 in model 634.0 with code MS5 (Euro V) with Liquid Only Engine 457.9 in model 695.023/053 with code MS5 (Euro V) with Liquid Only Engine 924.9 in model 979.0 with code MS5 (Euro V) with Liquid Only Engine 924.9, 926.9 in model 368.002/004/006/100/104/106/115/117, 382.1, 384.0/223, 685.282/284/289/290/295, 979.2 with code MS5 (Euro V) with Liquid Only Engine 924.9, 926.9 in model 958.1 with code MS5 (BlueTec 5) with Liquid Only

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 1 Silnik › 14 Kolektor wydechowy, hamulec silnikowy, instalacja oczyszczania spalin › 14.40 Układ oczyszczania spalin, AdBlue — Seria 368 (modele 002, 004, 006, 100, 104, 106, 115, 117) · Seria 382 (modele 1**) · Seria 384 (modele 0**, 223) · Seria 634 (modele 0**) · Seria 685 (modele 282, 284, 289, 290, 295) · Seria 695 (modele 023, 053) · Seria 958 (modele 1**) · Seria 979 (modele 0**, 2**)

EinPAS 15 Silnik › 15.40 Układ wydechowy/ układ oczyszczania spalin › 15.40.13 Przewód sztywny/elastyczny/zawór — Seria 368 (modele 002, 004, 006, 100, 104, 106, 115, 117) · Seria 382 (modele 1**) · Seria 384 (modele 0**, 223) · Seria 634 (modele 0**) · Seria 685 (modele 282, 284, 289, 290, 295) · Seria 695 (modele 023, 053) · Seria 958 (modele 1**) · Seria 979 (modele 0**, 2**)

Dotyczy też silników/skrzyń biegów: 457 9**, 924 9**, 926 9**

AR14.40-B-2057A

Remove/install pressure limiting valve of pump module

23.07.2019

Engine

457.9 in model 634.0

with code MS5 (Euro V)

with Liquid Only

Engine

457.9 in model 695.023/053

with code MS5 (Euro V)

with Liquid Only

Engine

924.9 in model 979.0

with code MS5 (Euro V)

with Liquid Only

Engine

924.9, 926.9 in model 368.002/004/006/100/104/106/115/117, 382.1, 384.0/223, 685.282/284/289/290/295, 979.2

with code MS5 (Euro V)

with Liquid Only

Engine

924.9, 926.9 in model 958.1

with code MS5 (BlueTec 5)

with Liquid Only

Remove/install pressure limiting valve of pump module

B14.40-0165-09

1

Pump module

3

Screw plug on the pump module

5

Pressure regulating valve

2

Support

4

Hole

6

Puller tool

Remove

Warning

Risk of burn injuries and scalding when working at AdBlue lines and the components attached to them. Risk of injury to skin and eyes when handling AdBlue. Risk of poisoning caused by swallowing AdBlue

Pour AdBlue into suitable containers only. Wait until the pressure is released before starting any work on the exhaust aftertreatment system.

AS14.40-Z-0001-01A

1

Remover the pump module (1) from the support (2) and put it aside

Notes on use, material properties and handling of AdBlue®

AH14.40-B-0001-01A

2

Remove the screw plug from the pump module (3)

While removing the screw plug from the pump module (3), small amounts of liquid may leak.

3

Engage the threaded side of the puller tool (6) in the pressure relief valve (5), and extract it

During the pressure relief valve removal (5) small quantities of fluid can leak.

The puller tool (6) is included in the repair kit.

Install

4

Introduce the new pressure relief valve (5) with the hep of the obtuse side of the puller tool (6)


Ensure that no dirt enters the bore (4):
This may cause damage to the pump module (1).

5

Install a new screw plug on the pump module (3) with sealing ring

.Pump module screw plug

*BA14.40-B-1003-02G

6

Install the pump module (1) in the support (2)

.Pumps module in the support

*BA14.40-B-1001-02G

Exhaust gas after-treatment

Number

Designation

Engine 457.9, 924.9, 926.9 with Liquid Only

BA14.40-B-1001-02G

Pumps module in the support

Nm

17,6

Exhaust gas after-treatment

Number

Designation

Engine 457.9, 924.9, 926.9 with Liquid Only

BA14.40-B-1003-02G

Pump module screw plug

Nm

5

Powiązane dokumenty