sm2620w0101a

Replace gear control (GS) control unit on gate module

유형 sm · 주제 26.20 · 버전 0101 · 2006-07-25

적용 대상: TRANSMISSION 715.5 in MODEL 930, 932, 933, 934 with CODE (GS7) Gear control II TRANSMISSION 715.5 in MODEL 930, 932, 933, 934 with CODE (GS7) Gear control II with CODE (GE2) Electronic drive control II

“ko”(으)로는 제공되지 않아 영어(으)로 표시합니다.

위치

기능 그룹 2 섀시 › 26 수동변속기 › 26.20 전자-공압-회로 (EPS) - 기어제어장치 (GS) — 시리즈 930 · 시리즈 932 · 시리즈 933 · 시리즈 934

EinPAS 17 드라이브 트레인/액슬 › 17.35 기어 변속/기어 컨트롤 › 17.35.11 컨트롤 유닛/릴레이 — 시리즈 930 · 시리즈 932 · 시리즈 933 · 시리즈 934

EinPAS 45 데이터/정보 › 45.20 정보/조치 › 45.20.40 서비스 메저 — 시리즈 930 · 시리즈 932 · 시리즈 933 · 시리즈 934

엔진/변속기에도 적용: 715 5**

SM26.20-W-0101A

Replace gear control (GS) control unit on gate module

15.12.05

TRANSMISSION 715.5 in MODEL 930, 932, 933, 934 with CODE (GS7) Gear control II

TRANSMISSION 715.5 in MODEL 930, 932, 933, 934
with CODE (GS7) Gear control II
with CODE (GE2) Electronic drive control II

Replace gear control (GS) control unit on gate module

W26.19-1077-09

1 Housing

2 Seal

3 Valve seat

4 Sealing ring

5 Intermediate plate

6 Seal

7 Valve seats

8 Sealing ring

9 Sealing ring

A16 Gear control (GS) control unit

Y29 Splitter 1 solenoid valve (MS1)

Y30 Splitter 2 solenoid valve (MS2)

Y33 Gate 1 solenoid valve (MG1)

Y34 Gate 2 solenoid valve (MG2)

10 Sticker

11 Model plate

A Bolt

B Bolt

C Bolt

D Bolt

E Bolt

F Bolt

Checking

Removing

1

Connect STAR DIAGNOSIS

*WH58.30-Z-1049-13A

2

Read out parameters in gear control (GS) control unit (A16) using STAR DIAGNOSIS and note down

Parameters: Clutch wear, clutch wear correction factor, transfer case, construction site function and vehicle model.

3

Switch off ignition

4

Remove gate module

AR26.20-W-1005A

5

Detach gear control (GS) control unit (A16) from housing (1)

6

Remove splitter 1 solenoid valve (MS1) (Y29) and splitter 2 solenoid valve (MS2) (Y30)

7

Remove gate 1 solenoid valve (MG1) (Y33) and gate 2 solenoid valve (MG2) (Y34)

8

Detach intermediate plate (5) from gear control (GS) control unit (A16)

Scrap the removed gear control (GS) control unit (A16).

Install

9

Attach intermediate plate (5) to new gear control (GS) control unit (A16)

Install new gasket (6).

*BA26.20-N-1001-03A

10

Attach splitter 1 solenoid valve (MS1) (Y29) and splitter 2 solenoid valve (MS2) (Y30) to new gear control (GS) control unit (A16)

Check sealing rings (4) for damage and replace if necessary.

11

Attach gate 1 solenoid valve (MG1) (Y33) and gate 2 solenoid valve (MG2) (Y34) to new gear control (GS) control unit (A16)

Check sealing rings (4) for damage and replace if necessary.

12

Install gear control (GS) control unit (A16) on housing (1)

Install new sealing ring (8).

*BA26.20-N-1001-03A

13

Install gate module

AR26.20-W-1005A

14

Switch on ignition

15

Transfer parameters of old gear control (GS) control unit (A16) to new gear control (GS) control unit (A16) using STAR DIAGNOSIS

*WH58.30-Z-1049-13A

16

Disconnect STAR DIAGNOSIS

*WH58.30-Z-1049-13A

Shift gate module

Number

Designation

Transmission
715.500/507/510/
513/520/540
with code GS7

BA26.20-N-1001-03A

Bolt, control unit to intermediate plate

Nm

10

Commercially available tools

Number

Designation

WH58.30-Z-1049-13A

STAR DIAGNOSIS Compact diagnostic system for commercial vehicles

651 131 10 00

참조 문서