ar9160d0680b

Remove/install passenger airbag unit

유형 ar · 주제 91.60 · 버전 0116 · 2019-07-24

적용 대상: Model 901.6, 902.6, 903.6, 904.6, 905.6 with code SA6 (Airbag, co-driver)

“ko”(으)로는 제공되지 않아 영어(으)로 표시합니다.

위치

기능 그룹 3 구조 › 91 시트, 카우치, 보호장치 › 91.60 에어백, 보행자 보호 — 시리즈 901 (모델 6**) · 시리즈 902 (모델 6**) · 시리즈 903 (모델 6**) · 시리즈 904 (모델 6**) · 시리즈 905 (모델 6**)

EinPAS 27 수동형 안전/시트 안전 시스템 › 27.16 에어백 › 27.16.20 에어백 — 시리즈 901 (모델 6**) · 시리즈 902 (모델 6**) · 시리즈 903 (모델 6**) · 시리즈 904 (모델 6**) · 시리즈 905 (모델 6**)

AR91.60-D-0680B

Remove/install passenger airbag unit

23.07.2019

Model

901.6, 902.6, 903.6, 904.6, 905.6

with code SA6 (Airbag, co-driver)

Modification notes

25.07.2013

Disconnect battery and associated operation steps, removed

Operation step 1, 8, 9, 10

Remove/install passenger airbag unit

1

Stowage box/tray

2

Bolts

3

Retaining clips

4

Connector

5

Front passenger airbag

6

Bolts

7

Retaining clips

D91.60-1133-06

Remove/install

Warning

Risk of injury caused by performing testing or repair work on airbag or emergency tensioning retractor units.

Store airbag units with deployment side facing up; do not expose to temperatures greater than 100 °C. When working on these units, disconnect the power supply.

AS91.00-Z-0001-01D

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

Topical note

Notes on performing repair, body work and welding on vehicles with airbags and RTE units

AH91.00-P-0002-01M

Legal requirements on handling and storing airbags and emergency tensioning retractor units

AH91.00-P-0004-01A

Assessment of airbag and belt tensioner units in accident vehicles

AH91.00-P-0006-01B

1

Remove ignition key from ignition lock

2

Unclip front stowage box/tray (1), lift slightly and remove toward front

3

Unscrew retaining clip (3)

Installation: Pay attention to installation position.

4

Remove bolts (6)

Installation: Replace bolts (6).

Bolt, front passenger airbag to bracket

*BA91.60-N-1003-01A

5

Remove front passenger airbag (5) from the bracket a little until connector (4) on the right side is visible

6

Disconnect plug (4) from squib at gas generator

Installation: Connector (4) must audibly snap in.

When replacing the airbag unit, ensure proper and environmentally friendly disposal.

7

Install in the reverse order

8

Connect diagnostic system and perform quick test

9

Read out fault memory of airbag (AB) system and delete fault memory

Airbag

Number

Designation

Model 690.6, 901.6, 902.6, 903.6, 904.6, 905.6

BA91.60-N-1003-01A

Bolt, front passenger airbag to bracket

Nm

10 (1)

참조 문서