D91.40-0002-09
1 | Screw | 6 | Screw | 11 | Slider | ||
2 | Door seal | 7 | Squib plug | 12 | Height adjustment | ||
3 | Door seal (with load compartment sliding door) | 8 | Guide | 13 | Screw | ||
4 | Cover | 9 | Guide | 14 | Retaining clips | ||
5 | Inertia reel with emergency tensioning retractor | 10 | Retaining tab |
| Remove/install | ||
Warning | Risk of injury caused by performing testing or repair work on airbag or emergency tensioning retractor units. | Store airbag units with deployment side facing up; do not expose to temperatures greater than 100 °C. When working on these units, disconnect the power supply. | |
Topical note | Notes on carrying out repair work in the vehicle interior | ||
Topical note | Notes on performing repair, body work and welding on vehicles with airbags and RTE units | ||
Legal requirements on handling and storing airbags and emergency tensioning retractor units | |||
Assessment of airbag and belt tensioner units in accident vehicles | |||
1 | Remove ignition key from ignition lock | ||
2 | Remove screw/bolt (1) from seat belt at seat | Bolt, seat belt end fitting to seat base | |
3 | Detach door seal (2) off web of door cutout on the B-pillar | ||
4 | Detach door seal (3) from bar of sliding door cutout on the B-pillar | MODEL 901, 902, 903, 904, 905 with CODE T16 (Right load compartment sliding door) with CODE T19 (Left sliding door) | |
5 | Pry off cover (4) from B-pillar (clipped) and remove upwards | Installation: Remove retaining clips (14) from B-pillar and insert in paneling (4). | |
6 | Remove height adjustment (12) from slider (11) and pull seat belt out of height adjustment (12) | Installation: Insert guide (9) into retaining tab (10). | |
7 | Remove screw/bolt (13) on upper guide point | Bolt, belt guide to belt height adjuster | |
8 | Disconnect squib plug (7) at squib on inertia reel with emergency tensioning retractor (5) | ||
9 | Remove inertia reel with emergency tensioning retractor (5) and remove guide (8) at B-pillar | Bolt, seat belt retractor to B-pillar | |
Caution | Risk of injury. Injury may result when the tension in the spring in the automatic belt retractor is released. | Never disassemble automatic belt retractors. | |
10 | Remove seat belt with inertia reel with emergency tensioning retractor (5) | Pay attention to proper and environmentally friendly disposal when exchanging the automatic belt retractors with emergency tensioning retractor (5). | |
Installation: Note different version of the emergency tensioning retractor for the left and right side of the vehicle and its proper location in the catch. | |||
11 | Install in the reverse order | ||
12 | Connect diagnostic system and perform quick test | ||
13 | Read out fault memory of airbag (AB) system and delete fault memory |
Seat belts/emergency tensioning retractors |
Number | Designation | Model 690.6, 901, 902, 903.0/3/4, 904, 905 | Model 903.612/613 | |
BA91.40-N-1001-01B | Bolt, seat belt end fitting to seat base | Nm | 35 | - |
Seat belts/emergency tensioning retractors |
Number | Designation | Model 690.6, 901, 902, 903.0/3/4, 904, 905 | Model 903.612/613 | |
BA91.40-N-1002-01B | Bolt, belt guide to belt height adjuster | Nm | 35 | 35 |
Seat belts/emergency tensioning retractors |
Number | Designation | Model 690.6, 901, 902, 903.0/3/4, 904, 905 | Model 903.612/613 | |
BA91.40-N-1003-01B | Bolt, seat belt retractor to B-pillar | Nm | 35 | 35 |
참조 문서
- ah6800n000101s 차량 승객실에서의 정비 작업 실행 지침
- ah9100p000201m 에어백 유닛 또는 안전벨트 텐셔너 유닛이 장착된 차량에서의 정비 작업, 차체 작업, 용접 작업 실행에 관한 지침
- ah9100p000401a 에어백 유닛과 안전벨트 텐셔너 유닛의 취급 및 보관에 관한 법규
- ah9100p000601b 사고 차량의 에어백 유닛 및 안전벨트 텐셔너 유닛 평가
- as9100z000101d 에어백 유닛 혹은 안전벨트 텐셔너 유닛의 점검 작업 또는 정비 작업 중 상해 위험
- as9100z000201a 안전벨트 리트랙터 스프링 해제 시 상해 위험