S88.20-4544-09
1 | Bracket | 3 | Bracket | ||||
2 | Screw | 4 | Bolts |
| Check | ||
1 | Check gap dimensions "AD", "BB", "CA" and "CB" | ||
Observe transitions between bumper and engine hood and fenders. | |||
Gap dimensions | |||
Gap dimensions | |||
Gap dimensions | |||
Feeler gauge | |||
| Remove | ||
2.1 | Detach fender liner in area of front bumper until bracket (1) is accessible | When adjusting gap dimensions "BB". | |
2.2 | Detach front bumper on left or right side until bracket (3) is accessible | When adjusting gap dimensions "AD" or "CA" or "CB" on one side of vehicle. | |
2.3 | Remove front bumper | When adjusting gap dimensions "AD" or "CA" or "CB" on both sides of vehicle. | |
Adjust | |||
3 | Loosen corresponding bolt (2) | When adjusting gap dimensions "BB". | |
4 | Loosen corresponding bolts (4) | When adjusting gap dimensions "AD" or "CA" or "CB". | |
5 | Position front bumper and install left or right support | When adjusting gap dimensions "AD" or "CA" or "CB". | |
6 | Adjust corresponding gap dimension "AD", "BB", "CA" or "CB" | ||
The gap dimensions can be adjusted by adjusting the corresponding bracket (1, 3). | |||
When adjusting gap dimensions "BB" also observe gap dimension "BA". | |||
Observe transitions between bumper and engine hood and fenders. | |||
Gap dimensions | |||
Gap dimensions | |||
Gap dimensions | |||
Feeler gauge | |||
7 | Detach front bumper until bracket (3) is accessible and tighten bolts (4) finger-tight | If gap dimension "AD" or "CA" or "CB" is adjusted. | |
8 | Tighten corresponding bolt (2) finger-tight | If gap dimension "BA" or "BB" is adjusted. | |
9 | Position front bumper and install left or right support | If gap dimension "AD" or "CA" or "CB" is adjusted. | |
| Check | ||
10 | Check gap dimensions "AD", "BB", "CA" and "CB" | ||
Observe transitions between bumper and engine hood and fenders. | |||
Gap dimensions | |||
Gap dimensions | |||
Gap dimensions | |||
Feeler gauge | |||
If complaint present | |||
| |||
Repeat adjustment procedure | |||
11 | Tighten corresponding bolt (2) | If gap dimension "BB" is adjusted. | |
12 | Detach front bumper until bracket (3) is accessible and tighten corresponding bolts (4) | If gap dimension "AD" or "CA" or "CB" is adjusted. | |
| Install | ||
13.1 | Fasten front bumper | If gap dimension "AD" or "CA" or "CB" is adjusted. | |
13.2 | Fasten front fender liner | If gap dimension "BB" is adjusted. | |
Gap dimensions |
Number | Designation | Model 447, 448 except code W65, W68 | Model 447, 448 with code W65, model 447, 448 with code W68 | |||
BE60.00-N-1001-01J | Gap dimensions | Engine hood to headlamp | Dimension "AA" | mm | 2,5 (1,5) | 2,5 (1,5) |
Engine hood to fender at side | Dimension "AB" | mm | 4 (0,8) | 4 (0,8) | ||
Engine hood to fender at top | Dimension "AC" | mm | 3,5 (0,8) | 3,5 (0,8) | ||
Engine hood to radiator trim | Dimension "AD" | mm | 5 (1) | 5 (1) | ||
For picture, see | ||||||
Gap dimensions |
Number | Designation | Model 447, 448 except code W65, W68 | Model 447, 448 with code W65, model 447, 448 with code W68 | |||
BE60.00-N-1002-01J | Gap dimensions | Fender to headlamp | Dimension "BA" | mm | 0,3 (0,25) | 0,3 (0,25) |
Fender to bumper | Dimension "BB" | mm | 2 (1) | 2 (1) | ||
Fender to A-pillar | Dimension "BC" | mm | 2,6 (1) | 2,6 (1) | ||
Fender to front door | Dimension "BD" | mm | 4,5 (0,8) | 4,5 (0,8) | ||
Fender to longitudinal member | Dimension "BE" | mm | 4,5 (1,2) | 4,5 (1,2) | ||
For picture, see | ||||||
129 589 03 21 00
Feeler gauge