ar8370d5683e

Remove and install flame sensor

유형 ar · 주제 83.70 · 버전 0103 · 2003-09-29

적용 대상: MODELS 901.06#, 902.06# /07#, 903.06# /07#, 904.06# ## as of 753731 as of 3.11.97 with CODE (H11) Warm air auxiliary heater B3L-C compact heater MODELS 901.36# /37# /46#, 902.36# /37# /46# /47#, 903.36# /37# /46# /47#, 904.36# /46# ## as of 753731 as of 3.11.97 with CODE (H11) Warm air auxiliary heater D3L-C compact heater MODELS 901.66# /67#, 902.66# /67#, 903.66# /67#, 904.66# ## up to 382001 up to 11.3.02 with CODE (H11) Warm air auxiliary heater B3L-C compact heater MODELS 901.66# /67#, 902.66# /

“ko”(으)로는 제공되지 않아 영어(으)로 표시합니다.

위치

기능 그룹 3 구조 › 83 에어컨 › 83.70 보조히터, 추가히터, 추가히터 — 시리즈 901 (모델 06*, 36*, 37*, 46*, 66*, 67*) · 시리즈 902 (모델 06*, 07*, 36*, 37*, 46*, 47*, 66*, 67*) · 시리즈 903 (모델 06*, 07*, 36*, 37*, 46*, 47*, 66*, 67*) · 시리즈 904 (모델 06*, 36*, 46*, 66*)

EinPAS 39 히터/환기/에어컨 › 39.25 독립식 히터/보조 히터 › 39.25.12 센서/스위치/배선 — 시리즈 901 (모델 06*, 36*, 37*, 46*, 66*, 67*) · 시리즈 902 (모델 06*, 07*, 36*, 37*, 46*, 47*, 66*, 67*) · 시리즈 903 (모델 06*, 07*, 36*, 37*, 46*, 47*, 66*, 67*) · 시리즈 904 (모델 06*, 36*, 46*, 66*)

AR83.70-D-5683E

Remove and install flame sensor

8.9.97

MODELS 901.06#, 902.06# /07#, 903.06# /07#, 904.06# ## as of 753731 as of 3.11.97 with CODE (H11) Warm air auxiliary heater
B3L-C compact heater

MODELS 901.36# /37# /46#, 902.36# /37# /46# /47#, 903.36# /37# /46# /47#, 904.36# /46# ## as of 753731 as of 3.11.97 with CODE (H11) Warm air auxiliary heater
D3L-C compact heater

MODELS 901.66# /67#, 902.66# /67#, 903.66# /67#, 904.66# ## up to 382001 up to 11.3.02 with CODE (H11) Warm air auxiliary heater
B3L-C compact heater

MODELS 901.66# /67#, 902.66# /67#, 903.66# /67#, 904.66# ## up to 382001 up to 11.3.02 with CODE (H11) Warm air auxiliary heater
D3L-C compact heater

MODELS WD1##, WD2##, WD3##, WD6##, WD7## ### up to 382001 up to 11.3.02 with CODE (H11) Warm air auxiliary heater
D3L-C compact heater

Remove and install flame sensor

D83.70-1296-09

1 Seal

2 Cover

3 Bolt

4 Body-bound rivet

5 Upper casing half

11 Flame sensor plug

12 Flame sensor

13 Retaining spring

14 Insulating shells

15 Outlet shroud

6 Lower casing half

7 Heat exchanger

8 Glow plug

9 Auxiliary heating control unit

10 14-pin plug

Remove/Install

1

Remove heater unit

Models 901.0/3/4, 902.0/3/4, 903.0/3/4, 904.0/3/4 as of 753731 as of 03.11.97

AR83.70-D-5302G

Models 901.6, 902.6, 903.6, 904.6

Models WD1, WD2, WD3, WD6, WD7 up to 382001 up to 11.03.02

AR83.70-D-5302K

2

Remove heater from the housing

Models 901.0/3/4, 902.0/3/4, 903.0/3/4, 904.0/3/4 as of 753731 as of 03.11.97

AR83.70-D-5399C

Models 901.6, 902.6, 903.6, 904.6

Models WD1, WD2, WD3, WD6, WD7 up to 382001 up to 11.03.02

AR83.70-D-5399A

3

Unscrew bolt (3) and remove cover (2) with gasket (1)

Installation: Check gasket for damage and replace if necessary.

4

Unlock 14-pin plug (10) and disconnect from auxiliary heater control unit (9)

5

Detach connection lines from the glow plug (8)

6

Detach trim parts (5, 6, 14, 15)

AR83.70-D-5398-05C

7

Disconnect plug (11) of flame sensor (12) from auxiliary heater control unit (9)

Installation: Observe accurate cable routing.

8

Remove retaining spring (13) of flame sensor (12)

Installation: Replace retaining spring (13). Push on retaining spring using a suitable tool (arrows).

9

Remove flame sensor (12)

10

Install in the reverse order

참조 문서