D72.16-1356-09
1 | Lever | 6 | Cable (outer emergency release) | 11 | Cable (motor coupling lock) | ||
2 | Inner emergency release unit | 7 | Adjustment screws | 12 | Bracket | ||
3 | Lever | 8 | Cable distributor | 13 | Microswitch | ||
4 | Outer emergency release | 9 | Screw-type nipple | 15 | Nuts | ||
5 | Cable (inner emergency release) | 10 | Slider |
Danger ! | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Danger ! | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
| Notes on carrying out repair work in the vehicle interior | ||
| Remove | ||
1 | Remove lower sliding door paneling | ||
2 | Check control cables (5, 6, 11) for damage and ease of movement, if necessary, replace damaged and sluggish cables (5, 6, 11) | Control cable damaged or sluggish, see: | |
| |||
Replace control cable on locking system | |||
Remove, install drive motor for electric sliding door | |||
Control cable (inner emergency release) (5) | |||
Route control cables for closing system | |||
Check and adjust | |||
3 | Check play of control cables (5, 6, 11) and adjust if necessary | To adjust loosen nuts (15), turn adjustment screws (7) until play is present on control cables (5, 6, 11). Counter adjustment screws (7) with nuts (15). | |
Play, cable for emergency release on sliding door | |||
4 | Actuate lever (1) on inner emergency release (2) and arrest | Motor coupling must unlock completely and microswitch (13) must switch. If necessary, correct adjustment of cables (5, 11) or microswitch (13). | |
5 | Open sliding door | Sliding door can be opened without motor turning. If necessary correct adjustment of cables (5, 11) or check motor coupling. | |
Motor coupling does not disconnect, even though control cables are adjusted correctly, see: | |||
| |||
Remove drive motor for electric sliding door | |||
6 | Move lever (1) of inner emergency release (2) to initial position | ||
7 | Close sliding door | ||
8 | Actuate lever (3) on outer emergency release (4) and arrest | Motor coupling does not disconnect and microswitch (13) must switch. If necessary, correct adjustment of cables (6). | |
9 | Open sliding door | Sliding door can be opened without motor turning. | |
10 | Move lever (3) of outer emergency release (4) to initial position | ||
11 | Close sliding door | ||
| Install | ||
12 | Install lower sliding door paneling | ||
Learn in electric sliding door | |||
13 | Completely open sliding door with switch on center console and close again | ||
| Check | ||
14 | Perform function test |
참조 문서
- ah6800n000101s 차량 승객실에서의 정비 작업 실행 지침
- ar7216d221002a 잠금장치 케이블 배선
- ar7216d6610g 슬라이딩 도어 패널 탈, 장착
- ar7229d5900ch
- ar7240d1002c
- as0000z001101a 후드, 도어, 커버, 슬라이딩 루프 탈, 장착 및 설정작업 시 손가락이 끼이거나 눌려서 입을 수 있는 상해 위험
- as0000z001701a 모서리가 날카로운 차량 부품에서 절단상과 찰과상으로 인한 상해 위험