W33.25-1064-01
Left steering stop, shown on left-hand drive vehicle | ||||
1 | Stop screw | |||
2 | Jam nut | |||
Right steering stop, shown on left-hand drive vehicle | ||||
1 | Stop screw | |||
2 | Jam nut | |||
W33.25-1065-01
Danger | Risk of death caused by vehicle slipping or toppling off during lifting | Only lift vehicle at the lift support points specified by the vehicle manufacturer. | |
Warning | Risk of injury from being trapped in the swivel range of steered axles | Ensure that no persons or objects are in the swivel range of all steered axles when turning the steering wheel. Do not stand in the swivel range of the additional steering axle when the engine is running. | |
Topical note | Notes on maintenance and repair work | ||
Topical note | Special instructions for lifting and supporting vehicle | ||
Note on calculation of tightening torque when using insertion or socket tools with various effective lengths | |||
| Check | ||
1 | Move front wheels to straight-ahead position. | ||
2 | Position wheels of front axle on center of turn plates. | ||
3 | Set scales of turn plates to 0°. | ||
4 | Turn steering to left up to end stop and hold in this position. | ||
5.1 | Read off angle on scale on turn plate of left wheel. | On left-hand drive vehicles | |
Steering angle of inner wheel | |||
If the specified angle is not achieved, | |||
| |||
release counternut (2) of stop screw (1) on left steering knuckle, adjust steering stop by screwing in or unscrewing the stop screw (1), then lock stop bolt (1) with counternut (2). | |||
Jam nut to stop screw for steering stop | |||
5.2 | Read off the angle on the scale of the turn plate of the left wheel and the distance between the drag link and the tire of the right front wheel. | On right-hand drive vehicles | |
Steering angle of inner wheel | |||
Distance, drag link to tire | |||
If the specified angle is not achieved or if the distance between the drag link and tire is too small, | |||
| |||
release counternut (2) of stop screw (1) on left steering knuckle, adjust steering stop by screwing in or unscrewing the stop screw (1) taking the distance between the drag link and the tire into consideration, then secure stop screw (1) with counternut (2). | |||
Jam nut to stop screw for steering stop | |||
6 | Turn steering to right up to end stop and hold in this position. | ||
7.1 | Read off the angle on the scale of the turn plate of the right wheel and the distance between the drag link and the tire of the left front wheel. | On left-hand drive vehicles | |
Steering angle of inner wheel | |||
Distance, drag link to tire | |||
If the specified angle is not achieved or if the distance between the drag link and tire is too small, | |||
| |||
release counternut (2) of stop screw (1) on right steering knuckle, adjust steering stop by screwing in or unscrewing the stop screw (1) taking the distance between the drag link and the tire into consideration, then secure stop screw (1) with counternut (2). | |||
Jam nut to stop screw for steering stop | |||
7.2 | Read off angle on scale on turn plate of right wheel. | On right-hand drive vehicles | |
Steering angle of inner wheel | |||
If the specified angle is not achieved, | |||
| |||
release counternut (2) of stop screw (1) on right steering knuckle, adjust steering stop by screwing in or unscrewing the stop screw (1), then lock stop bolt (1) with counternut (2). | |||
Jam nut to stop screw for steering stop | |||
8 | Move front wheels to straight-ahead position. | ||
9 | Check hydraulic steering limiter, adjust if necessary. | If the steering stop was readjusted. | |
참조 문서
- ah0000p001501cw 다양한 길이의 삽입 공구 혹은 소켓 공구를 사용할 때 조임 토크 산출에 관한 지침
- ah0060n010001b 차량을 들어 올리고 정비대 위에 올려 놓는 작업 관련 지침
- ah4620n000101h 유지 보수 및 정비 작업 지침
- ar0060w200001h 회전 플레이트 위로 차량 위치시키기
- ar4620w1100ne
- as0000z003201a 차량을 들어 올릴 때 차량이 떨어지거나 틸팅되어 발생할 수 있는 생명의 위험
- as4600z000201a 조향된 차축의 회전 영역에서 정지 시 끼임에 의한 상해 위험