W20.10-1095-08
1 | Coolant pump | 3 | Banjo bolt | ||||
2 | Coolant line | 4 | Connection piece |
Danger ! | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut. | |
Danger ! | Risk of injury caused by pinching or crushing when working on springs or spring bodies that are under tension | Use only approved tensioning devices; additionally screen off hazardous area if necessary. Check special tools for damage and proper operation (visual inspection). Wear protective gloves. | |
Danger ! | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Danger ! | Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. | |
| Notes on avoiding damage through contamination and foreign objects | ||
| Notes on self-locking nuts and bolts | ||
| Notes on tilting the cab | ||
| Remove/install | ||
1 | Tilt cab | Installation: Only tilt back cab after the leak test. | |
2 | Remove soundproofing | Installation: Only install soundproofing after the leak test. | |
3 | Drain coolant at engine radiator | ||
4 | Slacken poly-V belt and take it off the belt pulley of coolant pump (1) | ||
| Damage profiles for a poly-V belt | ||
Installation: Check condition of poly-V belt; install poly-V belt if necessary. | |||
5 | Remove coolant thermostat | Engine radiator at the front. | |
6 | Remove coolant line (2) at coolant pump (1) | Installation: Replace sealing rings on the banjo bolt (3). | |
7 | Remove coolant pump (1) | Installation: Clean sealing surfaces. | |
Bolt, coolant pump to oil/coolant module | |||
Lubricant, rubber assembly 1 l | |||
8 | Install in the reverse order |
참조 문서
- ah0000n000101a 자가 잠금식 볼트와 너트 관련 지침
- ah0000n500001h 불순물 및 이물질에 의한 손상 방지 지침
- ah6080n000301a 캡 틸팅 관련 지침
- ap1322d135101a V벨트 손상 유형
- ar1320w100001md 벨트 드라이브 운동 패턴
- ar1322w390205md
- ar2000w1142ne
- ar2010w2461ne
- as0000z000101a 프리텐셔닝된 스프링 또는 스프링 장치에서 작업 시 끼이거나 눌려서 입을 수 있는 상해 위험
- as0000z000501a 엔진이 작동 중인 상태에서 급발진에 의한 사고 위험 시동 또는 구동 중인 엔진 근처에서 작업할 때 차량에 부딪히거나 열에 의한 상해 위험
- as2000z000101a 뜨거운 냉각수 분출 시 입은 화상에 의한 피부와 안구의 상해 위험 냉각수의 음용으로 인한 중독 위험
- as6080z000101a 캡이 틸팅될 때 신체의 일부가 끼이거나 눌려서 발생하는 상해 위험