ar1440b2039a

Attach/remove test facility for checking the AdBlue metering amount on metering device

유형 ar · 주제 14.40 · 버전 0201 · 2019-08-01

적용 대상: Engine 924.9 in model 368, 384.0/2, 685.282/284/289/290, 979.2 Engine 926.9 in model 368, 382.17/18, 384.0

“ko”(으)로는 제공되지 않아 영어(으)로 표시합니다.

위치

기능 그룹 1 엔진 › 14 배기 매니폴드, 엔진 브레이크, 배기가스 정화장치 › 14.40 배기가스 후처리, AdBlue — 시리즈 368 · 시리즈 382 (모델 17*, 18*) · 시리즈 384 (모델 0**, 2**) · 시리즈 685 (모델 282, 284, 289, 290) · 시리즈 979 (모델 2**)

EinPAS 15 엔진 › 15.40 배기 시스템/배기가스 후처리 시스템 › 15.40.51 펌프/정량기/노즐 — 시리즈 368 · 시리즈 382 (모델 17*, 18*) · 시리즈 384 (모델 0**, 2**) · 시리즈 685 (모델 282, 284, 289, 290) · 시리즈 979 (모델 2**)

엔진/변속기에도 적용: 924 9**, 926 9**

AR14.40-B-2039A

Attach/remove test facility for checking the AdBlue metering amount on metering device

15.07.2019

Engine

924.9 in model 368, 384.0/2, 685.282/284/289/290, 979.2

Engine

926.9 in model 368, 382.17/18, 384.0

Attach/remove test facility for checking the AdBlue metering amount on metering device

1

Test injection piping

2

Test injection nozzle

4

Hose

5

Manifold

6

Plastic strap

W14.40-1370-06

Install

Warning

Risk of burn injuries and scalding when working at AdBlue lines and the components attached to them. Risk of injury to skin and eyes when handling AdBlue. Risk of poisoning caused by swallowing AdBlue

Pour AdBlue into suitable containers only. Wait until the pressure is released before starting any work on the exhaust aftertreatment system.

AS14.40-Z-0001-01A

1

Open the engine compartment access cover

Notes on use, material properties and handling of AdBlue®

AH14.40-N-0001-01A

Access to carry out maintenance and repair work, varies with body type/make.
Refer to the body makers instructions.

2

Cover the starter with a clean cloth

Before the injection piping removal, the starter should be covered with a clean cloth to be protected against occasional AdBlue drops, because it can damage the starter and the connected wire harnesses.

3

Remove injection line


.

AR14.40-B-2001A

4

Install the device for the test of dosage volume of AdBlue

Test facility for checking the AdBlue metering mount of the metering device

.

WF58.50-B-1440-04A

5

Install the test injection piping (1) with the test injection nozzle (2) in the metering device

6

Connect the hose (4) in the test injection nozzle (2), and fix it with a plastic strap (6)

7

Put the collector (5) on the floor

Be sure the hose (4) is not folded.

The test is performed by means of the STAR DIAGNOSIS.

Remove

8

Remove the test device in the metering device

After use, clean the device with clear water.

9

Install a new injection line


.

AR14.40-B-2001A

The injection line must be replaced after each removal.

참조 문서