ar0330p5000rt

Removing/installing the retaining lock for crankshaft / ring gear

유형 ar · 주제 03.30 · 버전 0101 · 2012-02-16

적용 대상: ENGINE 113.971 in MODELS 251.075 /175

“ko”(으)로는 제공되지 않아 영어(으)로 표시합니다.

위치

기능 그룹 1 엔진 › 03 파워트레인 › 03.30 플라이휠, 드라이버 디스크, 진동댐퍼, 플라이휠 링기어 — 시리즈 251 (모델 075, 175)

EinPAS 15 엔진 › 15.15 연소 엔진 전체/엔진 블럭/크랭크 어셈블리 › 15.15.41 크랭크샤프트/플라이휠/클러치 디스크 — 시리즈 251 (모델 075, 175)

엔진/변속기에도 적용: 113 971

AR03.30-P-5000RT

Removing/installing the retaining lock for crankshaft / ring gear

14.2.12

ENGINE 113.971 in MODELS 251.075 /175

Removing/installing the retaining lock for crankshaft / ring gear

P03.30-2107-05

1 Retaining lock

Removing/installing

Danger!

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Danger!

Risk of injury caused by moving parts that can pinch, crush or, in extreme cases even sever extremities.

No parts of the body or limbs should be within the operating range of the mechanism when components are in motion.

AS00.00-Z-0009-01A

Danger!

Risk of explosion caused by oxyhydrogen gas. Risk of poisoning and caustic burns caused by swallowing battery acid. Risk of injury caused by burns to skin and eyes from battery acid or when handling damaged lead-acid batteries

No fire, sparks, open flames or smoking. Wear acid-resistant gloves, clothing and safety glasses. Only pour battery acid into suitable and appropriately marked containers.

AS54.10-Z-0001-01A

Notes on battery

All models

AH54.10-P-0001-01A

1

Switch ignition off, remove ignition key (transmitter key).

On vehicles with Keyless Go, code 889: Press Keyless Go start/stop button repeatedly until ignition is switched off.

2

Disconnect ground cable from battery

Insulate clamping device of the ground line in order to prevent inadvertent contact with the ground point of the battery.

AR54.10-P-0003RT

3

Raise vehicle with lifting platform

AR00.60-P-1000RT

4

Remove starter

AR15.30-P-7100RT

*BA15.30-P-1001-01A

*BA15.30-P-1002-01A

*BA15.30-P-1003-01A

5

Insert retaining lock (1) into starter opening

Slide the retaining lock into the starter opening (see arrow) and allow to latch into the ring gear. If required, continue turning the engine at the center Bolt for the crankshaft in the direction of rotation of the engine.

Retaining lock

*112589034000

6

Install in reverse order

7

Perform basic programming

AR00.19-P-0200RT

Starter

Number

Designation

Engine
113.971
in model 251.075/175

BA15.30-P-1001-01A

Nut for connection on circuit 30

Nm

14

BA15.30-P-1002-01A

Nut for connection on circuit 50

Nm

6

BA15.30-P-1003-01A

Bolt for starter on crankcase

Nm

40

Removing/installing the retaining lock for crankshaft / ring gear

Retaining lock

112 589 03 40 00

참조 문서