1 | Oil pan bottom section |
2 | Electrical connector |
5 | Retaining clamp |
S01.45-4529-11
1 | Oil pan bottom section |
3 | Oil pan top section |
4 | Screw |
D01.45-1128-05
Caution | Risk of injury to skin and eyes due to handling of engine oil. Risk of poisoning caused by swallowing engine oil | Wear protective gloves, protective clothing and safety glasses. | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Topical note | Notes on self-locking nuts and bolts | ||
Topical note | Notes on using electrical or pneumatic screwdrivers/impact wrenches | ||
| Remove | ||
1 | Remove lower engine compartment paneling | ||
2 | Drain engine oil | ||
| Engine oil and oil filter change | ||
3 | Disconnect electrical connection (2) | ||
4 | Remove electrical wiring harness from oil pan bottom section (1) | ||
5 | Remove screw/bolts of oil pan bottom section (1) | Almost completely remove the two opposing screw/bolts. | |
6 | Remove oil pan bottom section (1) | | |
To do this screw screws/bolts (4) into the pry off thread of the oil pan bottom section (1) and pry off oil pan bottom section (1). | |||
7 | Remove oil pan bottom section (1) | To do this remove the remaining screw/bolts for the oil pan bottom section (1). | |
8 | Remove screws (4) | ||
9 | Remove engine oil level sensor | Only when replacing oil pan bottom section (1). | |
| Clean | ||
10 | Clean sealing surfaces | ||
Loctite 7200 | |||
Loctite 7063 (400 ml) cleaning spray | |||
| Install | ||
11 | Install engine oil level sensor | Only when replacing oil pan bottom section (1). | |
12 | Apply sealant to sealing surface of the oil pan bottom section (1) | ||
Notes on sealant path for oil pan | |||
Sealant, Loctite 5970, 50 ml | |||
13 | Place oil pan bottom section (1) with seal on the oil pan top section (3) and tighten down screw/bolts | Oil pan bottom section to oil pan top section | |
14 | Attach electrical wiring harness at oil pan bottom section (1) | Check retaining clamps (5); inspect and replace, if necessary. | |
15 | Connect electrical connection (2) | ||
16 | Pour in engine oil | ||
| Engine oil and oil filter change | ||
| Check | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
17 | Check for leak tightness with engine running | Visual inspection only. | |
18 | Install lower engine compartment paneling |
참조 문서
- ah0000n000101a 자가 잠금식 볼트와 너트 관련 지침
- ah0000n001701a 전동식 또는 공압식 자동 드라이버 사용 관련 지침
- ah0145n000101we 오일팬 실런트 경로 지침
- ap1800s0101e 엔진 오일 교환 및 오일 필터 교체
- ar0100p005001a 실런트를 제거하십시오.
- ar1840s5111e
- ar6120s1105e
- ar6120s1105e
- as0000z000501a 엔진이 작동 중인 상태에서 급발진에 의한 사고 위험 시동 또는 구동 중인 엔진 근처에서 작업할 때 차량에 부딪히거나 열에 의한 상해 위험
- as0000z001001a 리프터에서 차량이 미끄러지거나 틸팅 시 생명의 위험
- as1800z000101a 엔진 오일 취급 시 피부와 안구의 상해 위험엔진 오일 음용으로 인한 중독 위험