D49.10-1172-09
1 | Rear muffler | 4 | Spring washer | 6 | Elastomer bearing | ||
2 | Soot particulate sensor downstream of SCR catalytic converter | 5 | Elastomer bearing | 7 | Elastomer bearing | ||
3 | Screw clamp |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Warning | Risk of burn injuries, suffocation and poisoning when working on the exhaust system and the components connected to it. Risk of suffocation and risk of poisoning caused by inhalation of gaseous and solid components of the exhaust. Risk of poisoning caused by skin contact with solid components of the exhaust. | Wear protective clothing and safety glasses. Use the extraction system. Move people out of the hazard area. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
| Remove/install | ||
1 | Raise vehicle. | ||
Topical note | Special instructions for lifting and supporting vehicle | ||
2 | Remove underbody paneling. |
| |
Installation: Install underfloor paneling only after the leak test. | |||
3 | Remove soot particulate sensor downstream of SCR catalytic converter (2) from rear muffler (1). | ||
Note on calculation of tightening torque when using insertion or socket tools with various effective lengths | |||
Do not disconnect electrical connector. | |||
Installation: Apply heat-resistant lubricating paste to thread of soot particulate sensor downstream of SCR catalytic converter (2). | |||
Soot particulate sensor to SCR catalytic converter/rear muffler | |||
Paste, hot lubrication 1 kg, DBL 6879.20 | |||
Box wrench bit | |||
4 | Release screw clamp (3). | Installation: Install new screw clamp (3). | |
Clamp, rear muffler to diesel particulate filter | |||
5 | Remove spring washer (4). | Installation: Check spring washer (4). | |
If spring washer (4) is damaged, | |||
| |||
replace damaged spring washer (4). | |||
6 | Remove rear muffler (1). | To do this, press rear muffler (1) out of elastomer bearings (5, 6, 7) toward the rear. | |
| Check | ||
7 | Check elastomer bearings (5, 6, 7) for wear and damage. | If damage and/or wear is present, | |
| |||
replace affected elastomer bearings (5, 6, 7). | |||
8 | Install in the reverse order. | ||
| Check | ||
9 | Check installation position and for unobstructed movement of rear muffler (1). | If installation position of rear muffler (1) is incorrect and/or unobstructed movement not OK, | |
| |||
Correct installation position of the rear muffler (1). | |||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
10 | Check exhaust system for leaks with the engine running. | Visual inspection only. |
000 589 71 03 00
Box wrench bit
参照文書
- ah0000p001501cw 異なる作用長の差込み、接続用ツールを使用する場合の 締付けトルク算出のための注意事項
- ah0000p500001a 汚れおよび異物による損傷防止に関する注意事項
- ah0060n010001ts リフト·アップおよびジャッキ·アップに関する注意事項
- ar0060d100004ts
- ar6130d1001ts
- as0000z000201a 高温になっているか、あるいは赤熱している部品を取り扱う場合に、火傷を負うあるいは失明する危険があります。
- as0000z000501a エンジン作動中に車両がひとりでに動き出す危険があります。 スタート時または作動中のエンジンに接触すると、巻き込まれて負傷をする、または火傷をする危険があります。
- as0000z001001a 車両がリフトから滑り落ちたり、傾くことによる生命の危険
- as0000z001701a 先の鋭がった部品による切り傷または擦り傷などの負傷の危険があります。
- as4900z000101a エグゾースト・システムおよび接続している構成部品での作業 では、火傷、窒息、および中毒の危険があります。 排気ガスの気体および固体の成分を吸い込むことによる窒息 �