ar2740d0205c

Remove/install radial shaft sealing ring on output flange

種別 ar · トピック 27.40 · バージョン 0104 · 2019-04-13

適用: Transmission 722.683/684/685 in model 906 with code ZG1 (Engageable all-wheel drive) Transmission 722.683/684/685 in model 906 with code ZG3 (Engageable all-wheel drive with gear reduction) Transmission 722.686 in model 906.1/2/6/7 with code ZG1 (Engageable all-wheel drive) Transmission 722.686 in model 906.1/2/6/7 with code ZG3 (Engageable all-wheel drive with gear reduction)

「ja」では利用できません。英語で表示しています。

位置付け

機能グループ 2 シャーシ › 27 オートマチック・トランスミッション › 27.40 ハウジング — シリーズ 906

EinPAS 17 駆動装置/アクスル › 17.20 トランスミッション › 17.20.41 フランジ — シリーズ 906

エンジン/トランスミッションにも適用: 722 683, 722 684, 722 685, 722 686

AR27.40-D-0205C

Remove/install radial shaft sealing ring on output flange

12.04.2019

Transmission

722.683/684/685 in model 906

with code ZG1 (Engageable all-wheel drive)

Transmission

722.683/684/685 in model 906

with code ZG3 (Engageable all-wheel drive with gear reduction)

Transmission

722.686 in model 906.1/2/6/7

with code ZG1 (Engageable all-wheel drive)

Transmission

722.686 in model 906.1/2/6/7

with code ZG3 (Engageable all-wheel drive with gear reduction)

Remove/install radial shaft sealing ring on output flange

Shown without connecting flange

1

Collar nut

2

Output flange

3

Radial shaft sealing ring

D27.40-1105-06

Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Remove/install

1

Move the selector lever to the P position

2

Raise vehicle

AR00.60-D-1000H

3

Remove propeller shaft to rear axle from transfer case and tie up on substructure

AR41.10-D-0050H

4

Remove propeller shaft to front axle from transfer case and tie up on substructure

AR41.10-D-0070H

5

Remove transfer case

AR28.10-D-0100H

6

Remove output flange(2)

AR27.50-D-0620-02B

Collar nut, output flange to output shaft

*BA27.50-N-1001-01A

Socket wrench bit

*126589020900

Puller

*000589893300

Drift

*716589011500

7

Remove radial shaft sealing ring (3)

Installation: Install a new radial shaft sealing ring (3).

Drift

*140589121500

8

Install in the reverse order

Gear set

Number

Designation

TRANSMISSION 722.683/684/685/ 686

BA27.50-N-1001-01A

Collar nut, output flange to output shaft

Nm

200

Remove/install radial shaft sealing ring on output flange
Remove/install radial shaft sealing ring on output flange
Remove/install radial shaft sealing ring on output flange
Remove/install radial shaft sealing ring on output flange

716 589 01 15 00

Drift

140 589 12 15 00

Drift

000 589 89 33 00

Puller

126 589 02 09 00

Socket wrench bit

参照文書