ar2645d0011b

Remove/install radial shaft seal for output flange

種別 ar · トピック 26.45 · バージョン 0100 · 2009-03-18

適用: TRANSMISSION 711.651 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange TRANSMISSION 711.660 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange TRANSMISSION 711.680 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange TRANSMISSION 711.685 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange

「ja」では利用できません。英語で表示しています。

位置付け

機能グループ 2 シャーシ › 26 マニュアル・トランスミッション › 26.45 PTO、PTO用トランスミッション — シリーズ 906

EinPAS 17 駆動装置/アクスル › 17.45 パワーテイクオフ › 17.45.60 シャフト/ギアホイール/シンクロナイザセット/フランジ — シリーズ 906

エンジン/トランスミッションにも適用: 711 651, 711 660, 711 680, 711 685

AR26.45-D-0011B

Remove/install radial shaft seal for output flange

6.3.09

TRANSMISSION 711.651 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange

TRANSMISSION 711.660 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange

TRANSMISSION 711.680 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange

TRANSMISSION 711.685 in MODEL 906 with CODE (N07) Power take-off countershaft (2b) with flange

Remove/install radial shaft seal for output flange
Remove/install radial shaft seal for output flange

D26.45-1006-01

Shown on transmission 711.680

1 Radial shaft seal

2 Output flange

3 Washer

4 Screw

5 Oil filler plug

D26.00-1104-01

Remove/install

Danger!

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.

AS00.00-Z-0010-01A

1

Raise vehicle

AR00.60-D-1000H

2

Secure vehicle on vehicle lift

AR00.60-D-0100H

3

Disconnect propeller shaft from output flange (2)

*BA41.20-N-1001-01A

4

Remove output flange (2)

AR26.45-D-0070-01A

*BA26.45-N-1001-01A

*901589000700

*000589653300

5

Remove radial shaft sealing ring (1).

Installation: Replace radial shaft seal (1). Clean seat of radial shaft sealing ring (1) and coat sealing lip with transmission oil before installing

*716589001500

6

Install in the reverse order

7

Unscrew oil filler screw (5) and check transmission oil level, correct if necessary

The automatic transmission fluid must be at the oil filler hole

Gear oils (Sheet 235.10)

Sheet 235.10

BB00.40-P-0235-10A

8

Screw in oil filler screw (5)

*BA26.40-N-1002-01A

Transmission housing

Number

Designation

Trans-mission
711.651

Trans-mission
711.660

Trans-mission
711.680

Trans-mission
711.685

BA26.40-N-1002-01A

Oil filler plug

Nm

50

50

34

34

PTO

Number

Designation

Transmissions 711.651/660 with code N05, N07

Transmissions 711.680/685 with code N05, N07

BA26.45-N-1001-01A

Output flange on power takeoff

Nm

110

110

Propeller shaft of PTO

Number

Designation

Model
906

BA41.20-N-1001-01A

Propeller shaft to PTO

Stage 1

Nm

15

Stage 2

°

90

Remove/install radial shaft seal for output flange
Remove/install radial shaft seal for output flange
Remove/install radial shaft seal for output flange

000 589 65 33 00

Drift

Puller

Pin wrench

901 589 00 07 00

716 589 00 15 00

参照文書