P35.30-2133-09
Shown on right side of vehicle
1 Rear axle shaft
2 Screw
3 Wheel bolt
4 Rear axle crossmember
9 Axle tube
10 Cover
11 Shock absorber
12 Extraction tool
5 Screw
6 Adapter
7 Extraction and installation tool
8 Bolts
Modification notes
| Remove/install | ||
1 | Remove left or right rear wheel | ||
2 | Unscrew bolt (2) of rear axle shaft (1) | To undo and tighten the bolt (2) screw two wheel bolts (3) into the wheel hub and counterhold wheel hub using a suitable tool. | |
Installation: Replace self-locking bolt (2) of rear axle shaft (1). | |||
| |||
3 | Support the rear axle crossmember (4) using a transmission jack, unscrew bolts (5) and lower the rear axle crossmember (4) | | |
Transmission jack gotis://H_00.10_01.0 | |||
4 | Remove wheel bolts (3) from wheel hub, position adaptation (6) to line up with the hole circle and attach to the wheel hub with all wheel bolts (3) | | |
5 | Position the extraction and insertion tool (7) to line up with the hole circle and fasten with bolts (8) to the adapter (6) | | |
| |||
6 | Press rear axle shaft (1) out of the wheel hub and detach extraction and insertion tool (7) as well as adapter (6) from the wheel hub | | |
| |||
7 | Support axle tube (9) with major assemblies lifting table or transmission jack | If both rear axle shafts (1) are removed simultaneously, the major assemblies lifting table should be used to support the axle tube (9). | |
Major assembly platform lift gotis://A_01_07.1 | |||
8 | Remove expansion clip on cover (10), remove cover (10) | ||
9 | Remove bolt of shock absorber (11) on axle tube (9) | | |
10 | Lower the axle tube (9) carefully and guide rear axle shaft (1) out of the wheel hub | Ensure that the inner ball joint of the rear axle shaft (1) is not pulled apart as it will be irreparably damaged as a result. | |
When lowering the axle tube (9) ensure that the rear spring does not fall out of its supports. | |||
Installation: Observe the correct seat of the rear spring in the supports on the axle tube (9) and on the frame-type integral support. Insert the shock absorber (11) into the support on the axle tube (9). | |||
11 | Raise the axle tube (9) and attach to the shock absorber (11) | Installation: Unscrew bolt on shock absorber (11) and lower the axle tube (9) until the rear axle shaft (1) can be inserted into the wheel hub. In the process ensure that the rear spring does not fall out of its supports. | |
12 | Undo rear axle shaft (1) using impact extractor and extractor tool (12) on transmission and remove. Afterwards seal the transmission opening with plug | Collect escaping transmission oil in a suitable container. | |
Installation: Do not damage radial shaft sealing ring otherwise it may leak. | |||
Installation: Replace circlip on the inner joint of the rear axle shaft (1). | |||
| |||
| |||
Plug | |||
13 | Install in the reverse order | ||
14 | Inspect transmission oil level, adjust to correct level if necessary |
Rear axle shock absorber
Rear axle carrier
Number | Designation | Model | |
BA35.10-P-1003-01F | Bolt, crossmember to frame-type integral support | Nm | 65 |
Rear axle shaft
Number | Designation | Model 451.3/4 | ||
BA35.30-P-1002-01D | Bolt, rear axle shaft to rear axle shaft flange | Stage 1 | Nm | 45 |
Stage 2 | ° | 90 | ||
221 589 04 33 00
Adaptation
Extraction tool
Extraction and insertion tool
Impact extractor
210 589 03 43 00
451 589 00 34 00
602 589 00 33 00
Repair materials
Number | Designation | Order number |
BR00.45-Z-1005-15A | Cap to transmission housing | A 451 261 00 33 |