Serie
it
ar3530b430004ga
Remove/install ring gear on differential housing
Tipo ar · tema 35.30 · versione 0104 · 2020-08-14
Valido per: Rear axle 741.710 in model 958 Rear axle 746.209/233 in model 934.2, 938.1, 958 Rear axle 746.213/230 in model 934.2 Rear axle 746.213/230 in model 958.2/4 except code ZC8 (New Final Drive-Top Performance Light) Rear axle 746.218/225 in model 382.1, 634.0 Rear axle 748.590/594 in model 934.2, 958.4
Non disponibile in “it”; mostrato in Inglese.
Collocazione
Gruppo funzionale 2 Telaio › 35 Asse posteriore › 35.30 Trasmissione, comando — Serie 382 (modelli 1**) · Serie 634 (modelli 0**) · Serie 934 (modelli 2**) · Serie 938 (modelli 1**) · Serie 958
EinPAS 17 Organi della trasmissione/assale › 17.51 Assale posteriore › 17.51.65 Ingranaggi e differenziale al ponte posteriore/trasmissione passante — Serie 382 (modelli 1**) · Serie 634 (modelli 0**) · Serie 934 (modelli 2**) · Serie 938 (modelli 1**) · Serie 958
Valido anche per motori/cambi: 741 710, 746 209, 746 213, 746 218, 746 225, 746 230, 746 233, 748 590, 748 594
AR35.30-B-4300-04GA
Remove/install ring gear on differential housing
Rear axle
741.710 in model 958
Rear axle
746.209/233 in model 934.2, 938.1, 958
Rear axle
746.213/230 in model 934.2
Rear axle
746.213/230 in model 958.2/4
except code ZC8 (New Final Drive-Top Performance Light)
Rear axle
746.218/225 in model 382.1, 634.0
Rear axle
748.590/594 in model 934.2, 958.4
Central actuation with differential
Number
Designation
Rear axle 748.590/594
BA35.30-B-1005-03L
Differential case ring gear
M18X1.5x75
1st stage
Nm
200
2nd stage
° angular
90
Central actuation with differential
Number
Designation
Rear axle 741.710. 746.209/213/218/225/230/233/301/302/314/315
BA35.30-B-1014-03J
Ring gear in the differential box
M18x1.5
1st stage
Nm
200
2nd stage
°
90
Number
Designation
Order number
BR00.45-Z-1112-06A
Lubricating oil for transfer case and drive axle, DB supply specification 6630.00 - SAE 85W90 and 90
Use corresponding commercially available repair materials.
1
Remove the screws (1) leaving four screws partially tightened on the opposite sides of the differential housing (3).
Loose only four screw turns not to damage the differential housing threads (3).
2
Support the ring gear (2) with the teeth side (arrows) on a proper base.
The differential housing (3) should not be supported.
3
Remove the ring gear (2) from the differential housing (3) striking the bolt heads (1) with a plastic hammer.
Hammer the screw heads (1) alternately until the ring gear (2) is loosened from the differential housing (3).
4
Assemble the guide screws (4) in the differential housing (3) and assemble the ring gear (2).
Before assembling, lubricate all movable parts with gear oil.
5
Assemble the screws (1) and tighten with the prescribed torque. .
For better tightening control, mark the screws (1) as they are being tightened.
