1 | Collar nut |
2 | Coupling flange |
3 | Screw |
4 | Lock |
5 | Threaded ring |
6 | Outside seal |
7 | Inside seal |
8 | Ball bearing |
9 | End cover of the interaxle differential |
10 | interaxle differential |
11 | Grooved ball bearing |
12 | Immobilizing key |
13 | Socket |
B35.30-0099-06
| Remove | ||
1 | Remove the interaxle differential with cap |
| |
2 | Remover the coupling flange (2) | Install the interaxle differential with cap in a suitable support to aid in removal | |
Retainer wrench | |||
Puller | |||
3 | Loose and remove the screw (3) and lock (4) from the threaded ring (5) | ||
4 | Remove the screw collar (5) | Fix the guide device and claw type wrench support on flange place | |
Torque multiplier | |||
Claw-type wrench | |||
5 | Remove sealing (6) (7) from threaded ring (5) | Drift | |
6 | Remove the cap (9) interaxle differential (10). | ||
7 | Disassemble the interaxle differential (10) |
| |
8 | Remove the longitudinal block |
| |
9 | Remove the grooved ball bearing (8) by tapping using a suitable puncture inside the cap | ||
| Install | ||
10 | Install the grooved ball bearing (8) on the cap (9) | Use an appropriated mandrel | |
11 | Install the longitudinal block |
| |
12 | Fit new seals (6) (7) under pressure on the screw collar (5) | Inner seal with single sealing lip, outer seal with ancillary sealing lip | |
Apply a sealing agent to the external surface of the seals | |||
Fill with lubricating grease the internal space between sealing lips | |||
Grease, DB supply specification 6804 - Class 267.0 | |||
Terolan 307/II, Dichtin 51, epple 22 sealant | |||
Drift | |||
13 | Install the interaxle differential (10) on the cap (9) | Use a gentle hammer | |
14 | Install the threaded ring (5) on the cap interaxle differential (9) | Fix temporarily with screws the interaxle differential on a suitable support or axle housing. Fix the guide device and claw type wrench support on flange place (2) | |
Apply a sealing agent on the screwed surface of the ring | |||
Threaded ring on longitudinal differential's cover | |||
Terolan 307/II, Dichtin 51, epple 22 sealant | |||
Torque multiplier | |||
Claw-type wrench | |||
15 | Lock the threaded ring (5) with lock (4), and screw (3) | ||
16 | Install the coupling flange (2) | Lock the nut with collar (1) with puncture on axle notch | |
Nut fastening the front transmission shaft's coupling flange |
Longitudinal differential |
Number | Designation | Rear axle 745.0/9 in Type 693ERear axle 745.5 in Type 386.059/384/387/389 | Rear axle 741.930/931 in Type 693.348/386/396ERear axle 741.950/951 in Type 958.1ERear axle 743.104/106ERear axle 743.132/143 in Type 386.354ERear axle 743.149 in Type 386.367/369ERear axle 743.153 in Type 682.308ERear axle 746.8 in Type 693.386/396 | ||
BA35.30-B-1001-04B | Nut fastening the front transmission shaft's coupling flange | M40 | Nm | 850 | 850 |
Longitudinal differential |
Number | Designation | Rear axle 745.0/9 in Type 693ERear axle 745.5 in Type 386.059/384/387/389 | Rear axle 741.930/931 in Type 693.348/386/396ERear axle 741.950/951 in Type 958.1ERear axle 743.104/106ERear axle 743.132/143 in Type 386.354ERear axle 743.149 in Type 386.367/369ERear axle 743.153 in Type 682.308ERear axle 746.8 in Type 693.386/396 | ||
BA35.30-B-1002-04B | Threaded ring on longitudinal differential's cover | M135 | Nm | 1000 | 1000 |
035 589 01 33 00
Puller
000 589 02 13 00
Torque multiplier
312 589 15 15 00
Drift
717 589 00 31 00
Retainer wrench
302 589 01 07 00
Claw-type wrench
Repair materials |
Number | Designation | Order number |
BR00.45-Z-1018-01A | Terolan 307/II, Dichtin 51, epple 22 sealant | Use corresponding commercially available repair materials. |
BR00.45-Z-1107-06A | Grease, DB supply specification 6804 - Class 267.0 | Use corresponding commercially available repair materials. |