ar9129p1421g
Removing and installing seat height adjustment drive
Type ar · topic 91.29 · version 0103 · 2003-04-28
Applies to: MODELS 463.200 /204 /206 /207 /208 /209 /220 /221 /224 /225 /227 /228 /230 /231 /232 /233 /240 /241 /300 /304 /307 /308 /320 /321 /324 /325 /327 /328 /330 /331 with CODE (SB5) Electrically adjustable left front seat with CODE (SB6) Electrically adjustable right front seat
Where it sits
Function group 3 Body › 91 Seats, bunks, restraint systems › 91.29 Seats - electrical system — Series 463 (models 200, 204, 206, 207, 208, 209, 220, 221, 224, 225, 227, 228, 230, 231, 232, 233, 240, 241, 300, 304, 307, 308, 320, 321, 324, 325, 327, 328, 330, 331)
EinPAS 37 Interior equipment › 37.26 Front seat › 37.26.47 Seat adjustment — Series 463 (models 200, 204, 206, 207, 208, 209, 220, 221, 224, 225, 227, 228, 230, 231, 232, 233, 240, 241, 300, 304, 307, 308, 320, 321, 324, 325, 327, 328, 330, 331)
EinPAS 37 Interior equipment › 37.27 Rear seat › 37.27.47 Seat adjustment — Series 463 (models 200, 204, 206, 207, 208, 209, 220, 221, 224, 225, 227, 228, 230, 231, 232, 233, 240, 241, 300, 304, 307, 308, 320, 321, 324, 325, 327, 328, 330, 331)
EinPAS 37 Interior equipment › 37.28 Passenger seat › 37.28.46 Seat adjustment — Series 463 (models 200, 204, 206, 207, 208, 209, 220, 221, 224, 225, 227, 228, 230, 231, 232, 233, 240, 241, 300, 304, 307, 308, 320, 321, 324, 325, 327, 328, 330, 331)
AR91.29-P-1421G
| Removing and installing seat height adjustment drive
| 19.7.99
|
MODELS 463.200 /204 /206 /207 /208 /209 /220 /221 /224 /225 /227 /228 /230 /231 /232 /233 /240 /241 /300 /304 /307 /308 /320 /321 /324 /325 /327 /328 /330 /331
with CODE (SB5) Electrically adjustable left front seat
with CODE (SB6) Electrically adjustable right front seat
1 Screw for seat height adjustment motor
2 Bracket screws
3 Bracket
4 Plastic clip
5 Plug-in wiring plug connection
6 Plug-in wiring plug connection
7 Tie strap
M18m1 Seat height motor
M19m1 Seat height motor
| Remove/Install
|
|
|
1
| Move front seat all the way forward
|
|
|
2
| Remove the screws securing the seat height adjustment motor (1).
| Pull up the seat until access to the screws (2) and the plug-in wiring connection (5, 6) is available.
|
|
3
| Cut off the wire ties (7).
|
|
|
4
| Disconnect electrical connector (5, 6) from seat height motor (M18m1, M19m1)
| Mark terminals to prevent any risk of incorrect connections.
|
|
5
| Remove screws at bracket (2)
|
|
|
6
| Remove bracket (3) from seat frame.
| Installation: lightly grease plastic clip (4) before installation.
|
|
7
| Remove seat height motor (M18m1, M19m1)
|
|
|
8
| Install in the reverse order
|
|
|
9
| Run an operational check on front seat
| See Operating Instructions
|
|
