P82.60-9479-07
Shown with CODE 501 (360° camera) and CODE 810 (Sound system) and CODE 872 (Seat heater in rear) |
1 | Right load compartment trim | 3 | Damping material | |
2 | Hazard warning triangle |
Shown with CODE 501 (360° camera) and CODE 810 (Sound system) and CODE 872 (Seat heater in rear) |
4 | Electrical connectors (with CODE 501 (360° camera)) |
5 | Foam material (with CODE 501 (360° camera)) |
6 | Electrical connector (with CODE 501 (360° camera)) |
7 | Electrical line (with CODE 501 (360° camera)) |
8 | Bracket |
9 | Electrical connector (with CODE 872 (Seat heater in rear)) |
10 | Nut |
15 | Nuts |
N25/6 | Rear seat heater control unit (with CODE 872 (Seat heater in rear)) |
N148 | 360° camera control unit (with CODE 501 (360° camera)) |
P82.60-9480-11
P82.60-9481-07
Shown with CODE 501 (360° camera) and CODE 810 (Sound system) and CODE 872 (Seat heater in rear) |
8 | Bracket | 13 | Electrical connector with fiber optic cable | |
11 | Electrical connector (with CODE 810 (Sound system)) | 14 | Nut | |
12 | Electrical connector | A90/4 | Tuner unit |
Topical note | Notes on avoiding damage to optical fibers during repair work | ||
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
| Remove/install | ||
1 | Connect diagnostic system and perform initial startup of the tuner unit (A90/4) | When replacing tuner unit (A90/4). | |
| |||
2.1 | Switch off ignition and remove transmitter key from electronic ignition lock control unit | Model 218.9 | |
2.2 | Switch off ignition and remove KEYLESS-GO start/stop button from electronic ignition lock control unit | Model 218.9 | |
3 | Remove right load compartment trim (1) | ||
4 | Remove hazard warning triangle (2) | ||
5 | Remove dampening (3) | ||
6 | Disconnect electrical connectors (4) from 360° camera control unit (N148) | Model 218.9 | |
7 | Fold over foam material (5) as shown | Model 218.9 | |
8 | Disconnect electrical connector (6) | Model 218.9 | |
9 | Unclip electrical line (7) from bracket (8) | Model 218.9 | |
10 | Disconnect electrical connector (9) from rear seat heater control unit (N25/6) | Model 218.9 | |
11 | Loosen nuts (10) | ||
12 | Unscrew nuts (15) | ||
13 | Remove bracket (8) with tuner unit (A90/4) and place to one side with electrical lines connected | Installation: Ensure that electrical wiring harnesses are routed correctly. | |
14 | Disconnect electrical connector (11) | Model 218.9 | |
15 | Disconnect electrical connection (12) | ||
16 | Disconnect electrical connector with optical fiber (13) | ||
17 | Cover plug of electrical connector with optical fiber (13) and equipment connection on tuner unit (A90/4) | ||
18 | Remove bracket (8) with tuner unit (A90/4) | ||
19 | Unscrew nut (14) | When replacing tuner unit (A90/4). | |
20 | Remove tuner unit (A90/4) from bracket (8) | When replacing tuner unit (A90/4). | |
21 | Install in the reverse order |
Referenced documents
- ad0000p200004a Connect STAR DIAGNOSIS and read out fault memory
- ad0000p200004a
- ah5400p000101a Information on preventing damage to electronic components due to electrostatic discharge
- ah8260p000105ak Notes on avoiding damage to optical fibers during repair work
- ar6830p1180elx Remove/install load compartment inner side paneling